Having problems with your Hoover U8361-900 WindTunnel 2 Bagless Upright Cyclonic Vacuum ?

While the windtunnel is upright the suction is awesome. When you lower it and engage the brushes is looses suction. It will not pickup anthing on the floor

Answers :

Check the brushroll if it spins freely, replace the belts 38528-034 and 38528-035. and make sure the tensioner for the V belt engages when you release the handle and pull the head back
Repair Help & Product Troubleshooting for Hoover U8361-900 WindTunnel 2 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

While the windtunnel is upright the suction is awesome. When you lower it and engage the brushes is looses suction. It will not pickup anthing on the floor

Check the brushroll if it spins freely, replace the belts 38528-034 and 38528-035. and make sure the tensioner for the V belt engages when you release the handle and pull the head back ... Hoover U8361-900 WindTunnel 2 Bagless Upright Cyclonic Vacuum

Hoover 6446 900 WindTunnel Bagged Upright has little suction at the floor brush but plenty at hose if disconnected. It does not seem that there is anything blocking the inlet at the floor brush.

Check for a clog in the brush hose ... Hoover Tempo Widepath Upright Vacuum - Blue

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.

Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I have a hoover steamvac delux with 5 brush agitor..puts water on floor, but will not suction up. also leaks water on floor under cleaner when upright. why?

... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Brush doesn't spin. no suction felt at brush - Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Check that the brush has not become fouled with string, etc. If it still doesn't work try the following.\015\012\015\012Some Dyson's have a switch for the brush on the front of the handle. If yours does, please make sure its on. This m ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction My quicksteamer does not pull the water from the floor in. It makes a funny noise and the brush is very loose on the bottom.

Bissell has made this model along with all of the older cleaners obsolete along with the parts for them. I would buy new. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Brush does not turn because belt is loose - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

You need a new belt that isn't stretched. You can get a replacement here:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

X1.1 model has plenty of suction through the nozzle, but doesn't 'pull' across the floor anymore or pickup dirt when using upright

Assuming that the automatic height adjuster is working properly, most likely your Sebo needs a new brush roll because the bristles on the old one are worn to the limit. To test the height adjuster, put the machine in the normal operating position (wi ... Sebo Automatic X1 Bagged Upright Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.

The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.

... Hoover Vacuums

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.

... Eureka Vacuums

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

S7000 my miele upright vaccum cleaner looses it suction when on carpet mode, suction is perfect when upright (hose). The suction lasts for appox 5 mins when on the carpet and it stops.

... Miele Vacuums

Vacuum cleaner I am needing to buy a vacuum cleaner - the flooring in our house is mainly oregon pine with loose rugs. I suffer from back problems and find the cylinder vacuums cause a great deal of back strain. I have been told that an upright vacuum is not suitable for wooden floors - I would appreciate any advice, particularly if u know of an upright vacuum cleaner that works well on wooden floors Thank you

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=517227&thid=728380\015\012Vacuum cleaner\015\012Posted by che9 on Jul 01, 2008\015\012I need to buy a vacuum clea ... Electrolux EL7055A Bagless Canister Vacuum

Loss of suction in my Hoover Windtunnel bagless selfpropelled upright

There's also the possibility that the fan/impeller has stripped loose from the motor shaft and is basically sitting there while the motor turns. Also, you may have broken vanes on the fan/impeller that will drastically reduce the suction. Replacemen ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t

... Vacuums

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?

Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I get plenty of suction at the hose, and none at the brushes. Also, the vacuum will not remain upright when I push it up. It appears that the part that switches the suction from the hose to the brush area is not engaged.

I looked up the problem where the machine would not stand upright, used that solution, and it worked. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1040 seconds