Having problems with your Hoover UH5000 TurboPower WindTunnel Anniversary Upright Vacuum with Pet-Hair Tool, Self-Propelled, Bagged ?

Hoover windtunnel self propell switch jammed up and wont turn

\015 Self propell cable jammed and vacuum agitator brush will not turn when handle down. Self propelled button is stuck in on position.\015

Answers :

Repair Help & Product Troubleshooting for Hoover UH5000 TurboPower WindTunnel Anniversary Upright Vacuum with Pet-Hair Tool, Self-Propelled, Bagged

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover windtunnel self propell switch jammed up and wont turn


Here is manual > http://hoover.com/file/552/check out the link below ... Hoover UH5000 TurboPower WindTunnel Anniversary Upright Vacuum with Pet-Hair Tool, Self-Propelled, Bagged

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.


... Vacuums

Hoover Self-Propelled WindTunnel, U6434-900 on/off switch doesn't


... Vacuums

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover U6485900 Self-propelled windtunnel brushed do not turn


... Hoover U6485900 Bagged Upright Vacuum

Hoover windtunnel self-propelled - will not turn on


You probably need the switch replaced. It's fairly simple to do youself, and it is a known problem with these vacuums.\015\012You can order the switch from hoover for about $10 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover, self propelled windtunnel ,on off switch will not shutoff. the second the electrical plug is put in the wall socket, the vacum starts running and you cannot shut it down with the on off switch


... Hoover Vacuums

V belt on hoover windtunnel self-propelled will not tighten to turn brush


Is it stretched or worn? If it is you can get a replacement here:Windtunnel V Belt ... Vacuums

How do I fix the carpet/floor switch on a hoover windtunnel bagged self propelled


The carpet / floor switch is a mechanical assembly. the bottom cover needs to be removed to expose the screws for the hood cover to be removed. then the switch can be accessed for repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace rocker switch - Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover windtunnel self propelled vacuum has new belts but brush won't turn on carpet


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Just put handle on windtunnel u6401-9rm and the self propelled switch will not flip into self propel mode. is there an adjustment on the self propel part?


When installing the handle on this machine, you must be sure the on/off switch and the self propel button are both in the OFF position. The actual switch inside must also be OFF, and the metal fitting on the end of the power drive cable should be bet ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Hoover Windtunnel On/Off switch will not turn Off...Switch seems to work O.K. when pressed directly but not with handle switch...It will turn on but not off..Cam seems to be intact on switch actuator..How does switch come out? Thanx


Take the handle off, then remove the tool holder, then you can get to the switch. Just has tabs on each side of switch, depress them and push it out. These switches will do this after awhile, replacing them is usually the way to correct the problem ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda


You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums

Hoover Bagless Windtunnel - Self Propel feature not working


I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?


This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900


May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Self-Propelled WindTunnel U6436-900 cable problem


The flat belt should be changed if it has been longer than 9-12 months. Next I would remove the upper handle to inspect the top section of the control cable, sometimes it fray's and has a sponge feel (no positive control) to self propel. To set this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have hoover WindTunnel Self Propelled Vacuum


Greetings from GoVacuum,Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0752 seconds