Having problems with your Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner ?

My Hoover wind tunnel keeps overheating and the red I dictator is on. I have cleaned all filters and checked for clogs....could the motor have dust in it? How do I check?

Answers :

Okay. I read these posts and decided to take the advice of checking the hose.
I had cleaned all filters, checked all hose (as-is) and did belt checks, etc.
The indicator was always showing red and it would shut down after about 5 minutes.
It ended up being a clog that I discovered after taking the hose completely off and seeing a clump right where the hose detaches. I began swinging the hose round and round and sure enough, more cat hair clumpls shot out. Big clumps.
So, you literally need to check every inch of hose to find the culprit.
After that, my indicator stayed green and it works like a charm.
Best wishes, Mike D
Take the entire hose off that connects the attachments to the vaccum. Have someone hold one end to a light and look through the other end to see if you can see the light... if you cant-its clogged. Swing the hose in circles, the centripital force on the clog will force it out the end.
Repair Help & Product Troubleshooting for Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Hoover wind tunnel keeps overheating and the red I dictator is on. I have cleaned all filters and checked for clogs....could the motor have dust in it? How do I check?

Okay. I read these posts and decided to take the advice of checking the hose.I had cleaned all filters, checked all hose (as-is) and did belt checks, etc.The indicator was always showing red and it would shut down after about 5 minutes. ... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.

Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together

... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor

On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom

... Vacuums

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??

... Eureka Capture Upright Vacuum Vacuum

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put

... Panasonic Vacuums

Ive changed the filter and checked the hoses but vacuum doesnt pick up ...when its on the dust is being blown out the bottom of the vacuum....i took the canister off to test the suction its fine...also cleaned the filter ...help!

Have you check the roller brush and drive belt? It may be your belt has broke or is slipping and therefore not turning the brush.\015\012Turn on machine and power head see if brush is turning if it is put a small amount of pressure on the rol ... Kenmore Vacuums

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.

Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.

Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.

Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

I have a DC07 which is not picking up very well. I've cleaned the pre motor filter, was not aware of the post motor and will check. However, do the Dyson brush rollers wear to the point of not picking up things from carpet?

Hi The filter is only part of the cleaning process with a Dyson.\012\012I would suggest you get a 2 p peice and unscrew the plastic screws on the base. You will likely find that this area has clogged up. Clean this area out and put solepl ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac

Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

My bagless upright model v209af vacuum motor thermostat keeps shutting down after 3 minutes have checked for blockages and have just cleaned and dried all filters. euro pro

... Euro-Pro Vacuums

My dyson has started to give off an acrid smell when I use it. I have checked all areas for blockages, cleaned the removable filter and removed all hair from the brush but this has not helped. I am worried the motor is getting hot in use. Whats the best thing to do next? Thanks

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

One day I was vacuuming and it sounded like something went up inside somewhere and the motor, I assume,..... is frozen ..all it does is hum when I turn it on! I have changed the belt, filter and checked and cleaned all hoses... what could this be? THANK YOU, Gail

It's likely something got into the fan, is stuck there, is preventing the fan from turning, and so prevents the motor running. There's a good possibility the motor burned out because of this. If there's a strong smell of burning metal, this is prob ... Hoover Elite Rewind Bagless Upright VacuumVacuum

When switching the vacuum (DC17 Animal) over to the hard surface setting (so the beater brush is not spinning), the vacuum shuts off. I cleaned the dust bin and checked the filter. I also cleared the beater brush of hair or debris that was wrapped around it. It still shuts off. Ideas? Thanks.

The drive belt has probably broken. You can get a replacement belt here:Dyson DC17 Belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson has lost it's suction...i've cleaned all filters and checked all the hoses. The motor appears to be getting too hot

The filter housing can also be an issue. Check this:\015\012\015\012http://www.ehow.com/how_5870417_modify-dyson-prefilter-suct ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My savvy has lost suction. I checked for blockage in hose and is ok. The filter basket is clean. the motor runs strong. What else could it be?

Facing the back you will see 2 chanels one on the left where the hose comes out and one on the right that entends down into the base.start with the one on the left,its shaped like a j..there are 10 screws take those out and clean the chanel.be carefu ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

There is a burning smell when switched on - does this mean the motor is on its way out? The canister is empty and I have cleaned the filters and checked for any blockages

Basically, yes !\012\012New motors can be bought reasonably cheaply on eBay, but you'll need good DIY skills and some unusual tools (torx drivers) to do the job.\012\012Have a look at www.dysonmedic.com to see if you feel you can do it. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0736 seconds