Having problems with your Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner ?

My hoover wind tunnel cord is all the way out; will not rewind. Can I fix it myself?


Answers :

I took off the dust canister and then the 2 Phillips screws on top of the rewinder. I was searching how to get at the rewinder so I took out the HEPA filter and holder. I then pressed down on the rewind leaver and it rewound. I am not sure why but maybe what I removed was putting some pressure on the rewind mechanism or I just had good luck.
Repair Help & Product Troubleshooting for Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover wind tunnel cord is all the way out; will not rewind. Can I fix it myself?


I took off the dust canister and then the 2 Phillips screws on top of the rewinder. I was searching how to get at the rewinder so I took out the HEPA filter and holder. I then pressed down on the rewind leaver and it rewound. I am not sure why but ma ... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Hoover UH70120 WindTunnel TSeries problems with the cord. im a tech savy guy and have been trying to fix a cord after it was pulled to far out and now wont auto retract, but just cant find a way to pull the cord rewind mechanism out to work on it. Any advice


You will probably have to replace the cord winding mechanism. I have never had any luck trying to repair one. Cord retracters are great when they work but it seems like they always go bad before too long. On many units you can't even replace the cord ... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

I have a silverrodo and can't get the cord to fully rewind is there a way to fix this? thanks


It's probably a worn out spring. You'll probably need to take it in to the local Aerus Electrolux shop for replacement of the spring, and possibly the entire cordwinder. You can also call them and see if they're close enough for free pick up and de ... Electrolux Vacuums

Tangled cord on wind tunnel rewind t series - Hoover S3630 WindTunnel Bagged Canister Vacuum


... Hoover S3630 WindTunnel Bagged Canister Vacuum

The automatic cable rewind on my Morphy Richards pod vacuum cleaner keeps retracting. I'd rather it didn't work at all than be constantly pulling out the cord. Is there any way in to fix it or disable it?


Hi\015\012Not really. It means that the cord has been pulled roughly when its been plugged in and the retracter is getting weaker to hold the cord that has been pulled out. Generally though wipe the entire cord from the end of the machine with a dry ... Miele S251i Plus Bagged Canister Vacuum

How to fix the auto retract on the hoover wind tunnel


... Hoover WindTunnel Max Multi-Cyclonic Bagless Upright Vacuum, Blue,

The retractable cord is stuck all the way out and will not go back in. Is there a simple way to fix this "disaster"??? without taking vacuum apart that is. And this is not my exact vacuum but I figure the cord problem would go for all of them. Ours is a ORANGE HEPA 360 Kenmore Whisper Belt 12 amp with PowerMate Model # 116.29219800


... Kenmore 27915 Bagged Canister Vacuum

The cord rewind button for my electrolux vacuum cleaner is stuck so it always rewind the cord. how to fix it?


... Electrolux Vacuums

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?


Which model do you have.. ... Vacuums

Repplacing power cord on Hoover Wind tunnel (not self propelled)


I am thinking that the cord goes in on the back, just below the handle. Remove the handle, then from the front, remove the tool holder(#8), then you can get to where the cord comes in and hooks up.\015\012\015\012 ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover wind tunnel retractable power cord


... Vacuums

Repplacing power cord on Hoover Wind tunnel (not self propelled)


HiThis is HARD and you NEED electrical knowledge and IF NOT UP TO IT YOU COULD CAUSE PROBLEMS TO YOUR SELF AND OTHERS.You do not say what the problem is with the cord.If is it damaged then it needs to be replaced with a new one.and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover s3639 vacuum...cord does not rewind


I had the same problem with my Hoover s3639. The cord rewinder started squeaking, and retracted less and less of the cord each time, until it finally stopped retracting the cord at all. Here is what I did. I hope it will work for you as well. Ope ... Hoover S3639 WindTunnel Bagged Canister Vacuum

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord


... Hoover Vacuums

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please?


A bit late for the original questioner, but perhaps this will help someone else.\015\012\015\012There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about ... Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

How do i fix the retractable cord on a dyson dc08 to go in all the way and not only part way?


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Lux 5000 vacuum cord will not rewind it is pulled all the way out need to disassemble


This rewind is not easy to work on, I rewound my Eureka with much persistance. The vacuum shop didn't want to tackle this.\015\012 It's easy to cut your fingers on the spring. ... Vacuums

How to remove hoover wind tunnel cord reel?


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Automatic power cord rewind on Hoover S3630 vacuum is veru weak


... Hoover S3630 WindTunnel Bagged Canister Vacuum

Hoover rewind cord stuck


... Hoover WindTunnel Pet Rewind Upright Vacuum

I have an Electrolux EPIC 6500 SR canister. The power cord is pulled all the way out and will no longer retracted. How do I fix this?


This canister has a dog ear device on the rewind. If you can push the cord in the rewind spring is off track and the spring and spool will need to be reset by opening the vac. If the cord will not budge either way , by now it has likely begun t ... Electrolux Lux 7000 Bagged Canister Vacuum

Model UH70120 Hoover Wind Tunnel T Series Rewind Model UH70120 purchased at Target - bagless How can I put on the new Belt? I have taken it apart but cannot figure out how to change the belt. How?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Vaccum overheating I have a hoover u5458-900 wind tunnel and the auto shot off has kicked in for overheat protection. i've cleaned the entire thing and let it sit like i was supposed to but it still won't fully turn on and stay on. it will turn on for a few minutes and then shut off and just cycle like that for a few times. is there anything i can do to fix this or should i just clean it more (if possible)?


Either the motor protector is bad, or you have a clog in the hose or the dirt inlet by the brush roll. Are the filters clean? It is also possible that there is a problem with the motor. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0495 seconds