Having problems with your Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum ?

Hoover model U6425-920 falls backward

\015 This has been a good machine. Lately it has not been latching in upright position. Now it wants to fall backwards when you let go of it. What parts should I order to repair it?\012\012Kindest regards,\012\012Frank A Snyder MD\015

Answers :

It sounds like the handle release lever is bad if the unit will not stand up. It's common when those units get a little older. It is unlikely you'll need the rear handle assembly (the part with the filter housing) but it does happen. Inspect the latch on the handle assembly to make sure it's not too worn to know for sure. Chances are, the handle release lever is just spent.
Here's the part you're looking for:


http://vacuummedic.com/product.php?id=171



As long as you're into it the belts and roller are always a great investment. Replacing them will make it clean like new again. I'll include the links for those parts as well.


Flat Belt:
http://vacuummedic.com/product.php?id=6

V-Belt:
http://vacuummedic.com/product.php?id=485

Brush:
http://vacuummedic.com/product.php?id=484





Happy Vacuuming!
The Vac Dr.
Repair Help & Product Troubleshooting for Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover model U6425-920 falls backward


It sounds like the handle release lever is bad if the unit will not stand up. It's common when those units get a little older. It is unlikely you'll need the rear handle assembly (the part with the filter housing) but it does happen. Inspect the latc ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

Hoover model U6425 height adjustment - Hoover Elite U5061-900 Bagged Upright Vacuum


... Hoover Elite U5061-900 Bagged Upright Vacuum

Upright hoover keeps falling backwards


... Dyson Vacuums

How to detach handle from the Hoover vacuum cleaner model U6425-900?


Click here > http://hoover.com/file/496/ for the manual for full instructions.. ... Vacuums

Where would OIL come from by the right side back wheel?I have a hoover wind tunnle model # u6425-920. Does the drive moter have oil in it if so and it is leaking should we replace the motor?


The motor does not have oil in it. The onnly thing I can think of is that if soemone had tried to free up something by using a spray lubricant, and not it is running out. I've never seen this issue. You would have to let a repair shop look at it. ... Vacuums

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900


May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

Hoover Model U6425-920, Series Q 12.0. runs 3-5 minutes, shuts down on thermal reset. motor shaft and brush both turn freely. cannot detect any roughniss at all in shaft turning.


... Hoover Vacuums

On my Hoover SteamVac SpinScrub,Model F5915905 the middle brush fell out of socket. Keeps falling out. How can I fix this problem?


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

How do you install a new idler arm on the Hoover model U6425-900?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Savvy model U8174-900.. The beater brush only runs sometimes when I pull the unit backward. The handle switch seems OK but I cannot figure out why it is acting strange like this. Tilting the handle up or down does not seem to have an effect on this situaltion. Thanks for your help. Ron Simon


The Savvy has had its problems with the switch in the handle it will need to be replaced. Don the Vacuum Doctor Alb,N.M. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I have a Hoover self propelled WindTunnel vacuum( Model U6425-920) that stops in the middle of cleaning. I have changed the flat belt and I'm still experiencing the problem. I usually have to wait an hour or so b/4 it would work again. Any advise?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=632298\015\012Generic problem for all Vacuums\015\012I have a Hoover self\015\012Posted by thjunk2007 o ... Vacuums

Hoover Z 700 Model U9145-900


Try going to hoover.com and either email them or there is a number that you can call, this is hoover direct, so someone there should be able to help you. Have your model and serial numbers and purchase date handy in case they ask. It also has a 2 y ... Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Savvy Brush only runs when the vacuum is moved backwards


Replacing the entire upper handle assembly with OEM Part #48663238 will solve your issues, for a cost of about $35 plus shipping. ... Hoover U8185-900 Upright Vacuum

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and


The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

I have a hoover spinscrub carpet cleaner model F7221-900 I need to download a user manual for.But hoover website tells me they can,t find this model number. I have checked # several times and it is correct. whats up?


I just needed to clean the brushes I finally just found the clips on each side of the brush roller and pressed in towards center and was able to pull brushes out. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Need a front wheel assembly for my Hoover Tempo model u5144-900. I see similar looking Hoover wheel assemblies online for different models, will they fit mine?


The Tempo series cleaners look similar, but are different colors. The wheel assemblies will work if they look identical in appearance to yours. ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

Hoover U8185-900 motor shuts off when you move the cleaner forwards but it runs when the cleaner is moved backwards


... Hoover U8185-900 Upright Vacuum

Hoover steamvac dual v w/autorinse widepath model f7245900 leaks cleaning solution on bottom of tank when filling


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0626 seconds