Having problems with your Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum ?

Motor shaft getting really hot

\015 So that it melts the flat belt and starts to smoke. Any solution?\015

Answers :

Open up the area where the beater is with the belt off. Turn\015\012the beater by hand...if it turns hard, the bearings are jammed up with\015\012old grease or debris. You'll have to deal with that.
Repair Help & Product Troubleshooting for Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor shaft getting really hot


Open up the area where the beater is with the belt off. Turn\015\012the beater by hand...if it turns hard, the bearings are jammed up with\015\012old grease or debris. You'll have to deal with that. ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Motor shaft gets hot - Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The motor shaft on my G4 kirby gets very hot....any thoughts


Take it in for its service,sounds like it needs a good cleaning. ... Kirby Generation 3 Bagged Upright Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

My vac then steam 2in1stoped steaming motor runs gets hot but no steam


... Shark Steam Vacuum, 2-in-1 Vac-then-Steam

Bissell bagless motor shaft is too hot and melting belts


My guess is that the roller binds on the carpet (high pile?) and the motor shaft, glazed from use, spins without moving the belt and quickly burns a hote through it. I've had that experience! ... Bissell Vacuums

Belt and lifter getting hot right away on start up.


Hello,\015\012I would say that it is definitely running backwards. I have a guide to replacing the power switch that outlines the reassembly of the Kirby and tells you which carbon brush wire plugs into which hole on the power switch. Ea ... Kirby Ultimate G Bagged Upright Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

FQ95x...motor gets very hot very fast


These old style majestic always ran on the hot side but since its pushing 20 years old, you need to have it serviced my a filter queen service center. that will help with the heat problem and prolong the life of the machine. ... Rainbow 75th Anniversary Canister Vacuum

Motor gets hot in moments and shuts off


True, the motor has safety measures to stop it from overheating... that's why it shut down. You smelled something, so some kind of damage was done. It's possible that the over temp switch itself got fried. Doesn't sound too good from here. ... Filter Queen Majestic Canister Vacuum

When the vaccum is running the motor gets hot & smells & is very noisy.


Sounds like yu may have a clog, either in the inlet by the brush roll, or the hose. If the hose comes loose, see if there is suction there. If no suction then it is clogged. If suction, then the inlet maybe clogged. ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Vacuum motor shaft too hot


Check the brush roll ends, will they turn easily or is one frozen. If so, you need to replace the brush roll. If the motor turns on, it and the belt are trying to turn the brush roll and can't. Also check the ends where the brush roll sits in and ... Dirt Devil Featherlight Bagless Upright Vacuum

I have just replaced my Dyson DC14 Motor and now it blows the hepa filter out and filter cap off from under the bin the air is really hot. Is something wrong?


This video on the link below may help youhttp://www.youtube.com/watch?v=6HQx-gFA3MI ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The region of the motor gets very hot during use. What can I do?


The Hoover is likely built with a temperature overload protector, to shut down the unit if it gets excessively hot. All the units will get heat build-up from the suction motor during use. ... Hoover Vacuums

Motor gets hot and stops running


Is there suction?\015\012\015\012call bissell and do a walk through.. you have a clog somewhere and its killing that motor.. with the hose off (completely) the machine does it still have the problem? if no add a part. check again.. this m ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Burned out The best way for me to describe the problem is to post reviews I made on Amazon.com, which is where I purchased them. ________________ Based on my past experience, I bought another 6 months ago. I live in a very tiny 2 room apartment and do not vacuum lots of dirt. I noticed this new vac getting very hot to the touch where the motor is located with only a few minutes of use. Today it just STOPPED. When I felt the canister, it was HOT. It obviously has burned out. Upon closer inspect


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

I want to take the fan impellar off the motor to clean it. I cant seem to get the metal housing off of the motor. Do you have to take the nut off the impellar If so how do you stop the shaft from turning thank you.


Very simply you dont take the fan out of the motor. it was not made to be removed or cleaned because its not supposed o get dirty if your using good bags in the vacuum. the best you can do is blow it out with an air hose. ... Electrolux Epic 6500 Vacuum

I need to replace the brush motor on my Bissell 9400...I can't figure out how to remove the existing motor. Took the clip off but can't get the gear off the shaft and the hole in the side isn't large enough to push the gear through...what's the secret?


... Vacuums

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks


Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

The motor on my Dyson Animal DC07 is getting very hot. I've always kept the filters and such clean. Is there any maintenance I am to be doing with the motor?


Hi its Darran at Dyson.From your description of the problem, it sounds as though there is a lack of airflow to the motor which is caused by a blockage in the machine or a dirty filter. To check your machine for a blockage, ple ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1054 seconds