Having problems with your Hoover V1 SteamVac SpinScrub Vacuum ?

Water leaking from bottom and hose not connected

\015 I tried to clean my car upholstery and water didn't come out of attachment at first then came in dribbles meanwhile water was leaking from bottom. When I finished trying the bottom tank was dry, top was almost full and the hose on the bottom inside was not connected. How do I reconnect it?\015

Answers :

The hose just pushes on. You will have to take the top cover off to rehook up the hoses. There are scres on the bottom, then where the dirty water tank sits, there tabs that you have to unhook, then the cover will come off. Note: the filter inside the ditry water tank, leave a gap at the top to the filter. If you push the filter all the way up, it won't spray or suck up.
Repair Help & Product Troubleshooting for Hoover V1 SteamVac SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Water leaking from bottom and hose not connected


The hose just pushes on. You will have to take the top cover off to rehook up the hoses. There are scres on the bottom, then where the dirty water tank sits, there tabs that you have to unhook, then the cover will come off. Note: the filter inside ... Hoover V1 SteamVac SpinScrub Vacuum

ShopVac pump The waterhose connection is up high. The only way to get the water up to the level of the hose is to continually hold down the on button due to the automatic shut off after it fills to a certain level. On the bottom of the filter there is a hole. I am thinking there should be a small hose of some sort to put into that hole that would then lead up to the level of the water hose. Concept makes sense to me. But in the meantime, good old duct tape seems to have done the trick. Not exact


Hey thats great whatever works its what makes america great ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

How do you remove the swivel attachment from the bottom of the hose where it connects to the canister?


... Kenmore Vacuums

I have a miele s184 and on the same side where the hose connects to the bottom of the vacuum, the housing is very loose. It does not come apart , but it looks like it could. I cannot locate a screw or anything to tighten. Can you help.


... Miele S184 Powerhouse Bagged Upright Vacuum

Eureka 4D. Brush turns but not alot of suction. dust bunnies build up inside the hose at the bottom and at the dust brush connection. Seems to be very hot. ?????


Try cleaning the filters ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

HI! i am not sure what the part is called that i need for my DC07. I can point it out on the vacuum. i think it is a hose that connects the bottom part of the vaccuum to the bucket part...i am sorry that i am not more specific.


It is called an "AI VALVE" - it looks like a Tuba and has two buttons that you push to take it off the machine - it sits into the square hole above the wheel and connects to the round hole next to the dirt bin. Call the Dyson helpline to order the pa ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped


... Electrolux Guardian Bagged Canister Vacuum

Hose disconnected There is a clear circle on the part where the hose connects to the cannister (above the orange ball) that is in a position that has the hose disconnected. I can move the circle so that the hose connects, but it won't lock in that position. Help!


This video may help ... Dyson Ball DC24 Bagless Upright Vacuum

Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don't know what to use to reattach the hose to the black fitting. It looks like it was glued...not sure what kind. Any ideas?


Duct tape ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Rainbow shampooer The soap dispenser on my Rainbow is not dispensing soap when I flip the switch to 'soap' mode. All connections are intact. All plastic hoses are intact. What do you think is going on? The soap bottle connects to a little straw that appears to be free of obstruction, however, it connects into a sealed casing on the hose.


The little "wash/rinse" switch on some of the Aquamate units shuts off the soap flow by kinking the tube inside the housing. If you leave the switch in the rinse position (therefore, kinked) when you're done using it, it may dry in the kinked positi ... Rainbow E series Canister Wet/Dry Vacuum

I was checking the hose that attaches to the bottom circular peice and I lost the hose inside. How do I take the bottom off to reattach the hose?


Steps to take off the bottom are listed on page 19 of the manual HERE ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Water leaking out bottom with hose attached


The water hose plugs into the solution valve-pressure on the side of the noozle(bottom). There may be a water line that has come loose there, you will have to take the top off to get to it.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

Where do I connect the hose and it's attachments


You need the suction/blower connector on the hose:This must be for G4 or G3 model as later models had this part a bit different.For rest ... Kirby G4 Bagged Upright Vacuum

When I try to disconnect the hose in order to use the hand held hose with an attachment, the dust from the bottom flies into the air. How does this opening get blocked off to ensure the dust enters through the attachment and not the bottom?


It is a matter of Physics. It seems like you have it running when you change the hose. ?? That's a no-no.Basically you will have o take it apart until you know how it works or wont work ... Bissell Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

No suction Hello - any help with this would be much appreciated! I just changed the bag and filters. The machine runs, seems normal, but there is no suction. There is no blockage of the hose, as indicated by the fact that that little viewer window above where the hose connects to the unit is not showing the red portion that it shows when there is something blocking the hose (god, this is hard to describe!). If I disconnect the hose and put my hand over the hole, I feel some suction. But


Well, it actually sounds like there is a blockage. Try removing your hose and dropping something through it, like a quqrter. If it comes through, no clog. If it is clogged, I believe that machine has a blower on the upper part of the cleaner (mayb ... Miele S514 Solaris Electro Plus Vacuum

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?


Yes don. call the store where u rented and tell them. ... Vacuums

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

The red light comes on when the bag is not full (in fact I put in a new one). When the hose is removed, the light goes off. How do I clean the small hose that leads to the bottom of the vacuum and the main hose?


If it has a clog caused by a hair ball or some other object, a "properly bent" coat hanger can be used to fish it out. ... Vacuums

I have a Hoover 5899-100 Steamvac. The hose is cracked at the bottom. I am going to order a replacement hose, but can't figure out how to remove the old hose. are there instructions out there to do this.


... Vacuums

For Kenmore 116.27514700 Progressive powermate vaccuum, how do I take apart the hose from the connection into the canister? I have a short in the hose and want to replace just the hose.


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0409 seconds