Having problems with your Hoover V1 SteamVac SpinScrub Vacuum ?

I have a Hoover SteamVac F5914-900 that I purchased approx 6 mos ago. It just started having the following problem. When I turn the cleaner on there is a sudden burst of solution/foam that emits out to both sides from behind the brushes. How can I fix this??


Answers :

Mine has been doing that occasionally, and I have ordered the pump assembly, #H43582003 which several have suggested is where the problem is. This leak, along with loss of solution going to the hand tool, seems to indicate that the pump is not working properly, and is leaking. Something about a float getting stuck, which makes sense, cause it stops leaking when the unit is tilted back a couple inches.
Repair Help & Product Troubleshooting for Hoover V1 SteamVac SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hoover SteamVac F5914-900 that I purchased approx 6 mos ago. It just started having the following problem. When I turn the cleaner on there is a sudden burst of solution/foam that emits out to both sides from behind the brushes. How can I fix this??


Mine has been doing that occasionally, and I have ordered the pump assembly, #H43582003 which several have suggested is where the problem is. This leak, along with loss of solution going to the hand tool, seems to indicate that the pump is not workin ... Hoover V1 SteamVac SpinScrub Vacuum

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

My bissell 9400 pro heat steam cleaners sprayers are clogged again...how can I fix this with out taking it to a shop to get fixed?


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the w ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell 2x proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix it


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My trigger on my shark steam cleaner model SC507C does not work anymore. Where can I get one and how much? I need all contact info as I am in Canada. I really love this cleaner and would like to fix it. Jennifer


... Euro-Pro S3325 Handheld Steam Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

How to fix bissell deep cleaner water pump - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

My bissle proheat carpet cleaner/vaccuum has become clogged with the cleaner solution. As a result the cleaner solution does not reach the carpet when in operation. I had this fixed before at a local appliance store but they are now closed. I would like to do it it at home. Is there is simple solution to clean the system so it becomes functional.


Take apart the handle (a few screws) unclip the small clear hoses, use a pipe cleaner or small screwdriver to clear the hose from the crystalized cleaning solution that is blocking the hose. Put it back together and it will be like new. ALWAYS run ... Vacuums

The problem is that the cleaner is heavy to use and does not pull itself forward as it should. It has been back to the supplier 3 times but they have not fixed the problem. The LED's on the front flicker and I think it may be a problem with the sensor. If you have any info. on how the sensor works and where it is located it would be useful as well as any other suggestions to fix the problem please.


If it heavy then do some muscle work and body building ... Vacuums

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

How to fix wheels on hoover vaccum cleaner


I cant get the back wheels off my mach 3 hoover vacuum can anyone help? ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Rug doctor MPC2C carpet cleaner suddenly stopped.


... Rug Doctor Mighty Pro Mpc2c Carpet Cleaning Machine

Fixing my vacuum cleaner


Check to make sure that your agitator still spins. (Agitator = brush). If your agitator still spins, it eliminates your belt and agitator as likely culprits. The last possible solution would be that your vacuum is clogged. The grinding sound might be ... Vacuums

Fantom thunder vacuum cleaner how to fix problems


... Vacuums

My vacuum cleaner suddenly stopped


... Vacuums

Dyson upright My Dyson cleaner suddenly screemed at me and stopped with a puff of smoke and burning smell. I had just emptied the cylinder. It is five years old.


Hi this is an expensive repair and would probably be cheaper to buy new one the problem you have is with the motor bearings seizing its expensive to repair because when dyson made thes vacs they were made so you need special tool to take them apart s ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]


Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

Hi I have a Hoover Dust Manager Cyclonic 2200W cleaner. The cord became entabgled inside and I have taken it apart...please can you help me fix it?


... Hoover Vacuums

Trying to fix new belt to Hoover Turbo Power vacuum cleaner. Don't see how the belt becomes taut. Fitting it around the roller, there is nowhere to fit the belt to, it just sits loose.


I looked at the user instructions guide online and saw where the 'other end' of the belt should be fitted. It was extremely hard to fit but eventually managed it. Thanks for this solution site. I wouldn't hesitate to use it again. ... Hoover U5396-900 Turbo Power Vacuum

Houver Cleaner My self propelled windtunell baged Vacumn has a broken belt. The small visible one that is visible is intact. This is the thick belt. I cannot for the life of me figure out what to open and how to replace it. The model # is U6 401-9RM I keep asking for a manual online but it doesn't recognize this number. I am 67 yrs old broke and fix it challenged..lol can you help me?


Take off the bottom plate, The flat belt ges around the motor shaft and then around the bigger pulley by the V belt. It will stretch to o on.\015\012\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0552 seconds