Having problems with your Hoover V1 SteamVac SpinScrub Vacuum ?

Hoover spinscrub my brushes will not spin after being taken out to clean

Answers :

First do they turn easily by hand? Usually there is a plastic shaft that drives these brushes. If they are "seated" properly, the unit will not turn. The shaft is usually a "male" and fits into a "female" opening. If it is installing correctly, then I would see if any belts are off.
Repair Help & Product Troubleshooting for Hoover V1 SteamVac SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover spinscrub my brushes will not spin after being taken out to clean

First do they turn easily by hand? Usually there is a plastic shaft that drives these brushes. If they are "seated" properly, the unit will not turn. The shaft is usually a "male" and fits into a "female" opening. If it is installing correctly, then ... Hoover V1 SteamVac SpinScrub Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.

Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvav, spinscrub carpet cleaner, brushes won't rotate or spin

... Hoover SteamVac Spinscrub 50 Carpet Cleaner

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???

... Vacuums

Brushes won't spin on a Hoover Steamvac SpinScrub Model F5918-900

Well the hand tool works off the suction of the machine and has nothing to do with the turbine that controls the brushes. if you can get the part i can walk you through taking it apart. when you write back, let me know what the model num of your mach ... Vacuums

The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?

On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.

The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.

... Vacuums

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.

That's the way it's supposed to work. ... Vacuums

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the

Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover brushes stopped spinning


Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia

I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover dual v brushes won't spin - Hoover Steam Vac Dual V w/ SpinScrub Vacuum

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?

Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and

The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover FH50044 spin scrub. Brushes won't turn. All is clean. Brushes turn by hand when on the machine. Any help.

... Vacuums

Hoover Elite Deluxe rewind... Air flow indicator stays activated, after filter has been cleaned. Brushes spin, but very little suction. Dirt is not spinning in cup

... Hoover Vacuums

I have a hoover steam vac f5899-100 the brushes doesnt spin...everything else works but tha. we took the brushes apart to clean

There is no belt it is air the gears stick open it up and spin them free ... Hoover F5899-910 SteamVac Vacuum

The spin scrub brushes do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Try this: Make sure the setting is set to floor, then remove the little window (you might need a flat screwdriver to "pry" it up) and clean off the filter. If there is a blockage, the brushes will not spin! I hope this helps, if so, please give fe ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes on my hoover spinscrub model F7411900 wont spin

Vanger cheva in post 1 got the correct answer. I just disassembled my f7411900 with some difficulty and took the turbine apart. Sure enough the bearing on the shaft was froze from rust. I was able to free it up in a vice and screw driver big enough t ... Hoover Vacuums

Hoover spin scrub brushes won't turn

... Vacuums

I have a Hoover Steam Vac All Terran floor shampooer, I have taken apart the brushes and other parts to make sure there are no clogs, but it still is not spinning. What else can I do? the Motor is working fine. and the suction is fine too.

There may be some substances such as dust or sand stuck in the spinning parts of the wheel. The substances are restricting the mechanism to work properly and causing blockage in the rotating causing your problem. Cleaning every part of the motor's ro ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0912 seconds