Having problems with your Hoover V1 SteamVac SpinScrub Vacuum ?
Will not start again.
\015 When I plugged it in it started then turned off - now it will not start again. I check the Outlet and that was fine, I even tried a different outlet. When it went out I wiggled the cord thinking it was loose - it sparked but did not start up.\015
Possible bad plug or outlet - but 1st remove/replace tanks and try again at a different outlet. For some reason all Hoovers models have some sort of "shut off" if you hit a wall edge too hard or when you turn you make the machine off balance. The r& r of tanks always works for me when I get an unexpected shut off. Also - it will make that noise you hear when the tanks are full first - then shut off even though they are no where near full.....
If the cord sparked, then it is bad and needs replaement. If it sparked at the plug end, then replace the plug.
Repair Help & Product Troubleshooting for Hoover V1 SteamVac SpinScrub Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.
If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums
Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????
This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to "on." (If you're not sure whether it's on or off, just click it back ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Once again having vacuum problems, when I push the start red paddle it hesitates and won't fully starts. It makes the noice to start but then it shuts off. Makes noise to start but then promply
... Eureka 4700A Maxima Bagless Upright Vacuum
While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.
The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.
Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.
Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums
Won't start I have a miele, model # s2481 red vacuum. It will not start. When the button is pressed it feels normal, but nothing happens, it will not start. Is this a problem my handy husband can tackle?
It is most likely your cord winder. They are a little tricky to fix yourself. A repair shop will probably charge about $50. To fix it. The contacts where the cord winder plugs into the motor need to be cleaned and adjusted. Just don't let your r ... Vacuums
When I turn it on it doesn't start out in the circle motion but starts and than stops and than starts and than stops and moves erratically and than totally stops.
Try a different battery. If no go, you might have bad board or sensors. Basically, if the battery replacement doesn't fix it, get rid of it. Borrow a battery from someone else so you're not wasting your money for testing.\015\012\015\012-=/ Daf ... iRobot 5800 Scooba Vacuum
Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian
... Electrolux Vacuums
My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.
The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob
Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum
I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.
Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
My new H2O Mop Ultra (Danoz) seems to heat up ok then when the light switches to green and I start using it, the orange light comes back on as well as the green. Produces steam to start with but then it starts to spit water too and everything ends up wet. Any ideas on whats wrong or should I just send it back?
That is a major hardware fault, I have seen this numerous times with these H2O mop's... They seem to either work perfectly for a long while or have problems right off the bat. You definitely want to send this unit back and either get a refund or at ... Vacuums
My scooba when switched on starts to spray water then spins round faster than normal then starts to go backwards quite quickly then stops then continues to reverse more then stops & with the nor
... iRobot 5800 Scooba Vacuum
Chain saw starts runs, bur saw won't start next time it is needed, craftsman chain saw
Steam vacuum? no clue but on your chain saw make sure you check the choke. it would explain why it wouldn't start again. ... McCulloch MC1275 Steam Vacuum
My Dyson DC28 Beater Bar will stop turning then start again. Then it quits all together and after awhile it will start again.
Hi there, it's Jack at Dyson.I'm sorry to hear your DC28's brush bar seems to be working intermittently. It may be worth taking a look at the video I've attached below, as this shows the correct way to check the cleaner head for obstructions ... Dyson DC28 Animal Bagless Upright Vacuum
I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]
Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums
Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e
The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have a Miele s251i vacuum that was working just fine until I umplugged it (while running) and re-plugged it in at a closer socket. When I replugged it, it started for a second and then stopped. Will not start now whether we use the on/off switch or not...suggestions? Would also like to know how to disassemble the unit so I could check out the wiring with a multitester..thanks
I just had exactly the same problem. Opened the vac, checked the circuit\012 next to the motor and it can be clearly seen that the Triac burned thru\012 the PCB. Will replace it and check again. Vac bought long ago, works \012extremely well. ... Miele Vacuums
Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us
Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums
Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce
I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum
Hi! My name is george and i forgot how to start my cleaner. I have a bissel proheat # 7901-1. Can U send a copy of the start-up directions after I fill the water mix tank up?
I forgot how to start my Bissell Pro Heat Upright Wet/Dry Please advise ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Burning when the vacuum was started today it didn't sound like it should and then started to smell like the motor was burning. this is less than 1 year old!!!!
A guess: either there is something in the fans, stuck in the tubes or the belt is being held in position by debris causing it to burn. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti
You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums
Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc
Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum