Having problems with your Hoover V1 SteamVac SpinScrub Vacuum ?

Hoover model 5906-900 spinscrub

\015 The brushes have stopped moving, what can I do? The machine still works, sucks etc. Just doesn's scrub anymore. Thanks for any and all help. Mickie D.\015

Answers :

Solution for Hoover SteamVac (F7452-900) brushes not spinning
\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem should not happen as often as I see other people also having this problem. Must be a poor design on Hoover’s part. It takes about 30 minutes and a Phillips screw driver and wrench. Pretty easy, just have to remember what screws went where.
\015\012Remove brushes, and front suction cover
\015\012On the bottom of the machine:
\015\012Remove the 4 screws behind brushes which attach the top faceplate
\015\012Remove the 2 screws from base in the sunken holes
\015\012Remove the two long silver screws from base which connect all the way to turbine assembly
\015\012Stand machine upright
\015\012Remove the floor select switch handle
\015\012Remove 1 screw near the center beside the intake hole
\015\012Remove the 2 screws over the rear wheels
\015\012Remove faceplate cover, the front will need to be gently pried over the clear plastic part, be careful about the upright disengaging lever under faceplate, move it under the metal wire
\015\012Remove the 2 screws in the front of the turbine assembly
\015\012Remove the 2 hoses on either side
\015\012Disengage the bar on the floor selector switch
\015\012Pull out the turbine assembly
\015\012Remove the 4 screws and 3 clips to separate the assembly
\015\012Remove the filter (which is most likely clean since, cleaning this is the manufactures only solution)
\015\012Remove the large white gear and with a wrench remove ball bearing
\015\012Remove other large white gear
\015\012Note that the metal gear attached to turbine will not move (this was my problem), with a wrench gently grab metal gear and twist free. Spin turbine to make sure it moves freely.
Put everything back together again and you should be good to go.
The turbine is bad, you can either replace it or take it apart and clean it ou. They get gummed up and won't work. Number 16 on the picture.
Repair Help & Product Troubleshooting for Hoover V1 SteamVac SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a hoover spinscrub carpet cleaner model F7221-900 I need to download a user manual for.But hoover website tells me they can,t find this model number. I have checked # several times and it is correct. whats up?

I just needed to clean the brushes I finally just found the clips on each side of the brush roller and pressed in towards center and was able to pull brushes out. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n

... Vacuums

Vacums hoover model F5871-900 - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Don't know what you wont but here is manual > http://hoover.com/file/664/ ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac model f5857-900 manual - Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM

... Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM

Hoover model 5910-900 - Hoover Steam Vac Dual V w/ SpinScrub Vacuum

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Cant find manual for model f5880-900 hoover steanvac spinscrub dont know how to attach upholstery parts

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

On my Hoover SteamVac SpinScrub,Model F5915905 the middle brush fell out of socket. Keeps falling out. How can I fix this problem?

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?

On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I need users manual for Hoover Steam Vac Deluxe Spinscrub, model F5874-900

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie

The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not

Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes on my hoover spinscrub model F7411900 wont spin

Vanger cheva in post 1 got the correct answer. I just disassembled my f7411900 with some difficulty and took the turbine apart. Sure enough the bearing on the shaft was froze from rust. I was able to free it up in a vice and screw driver big enough t ... Hoover Vacuums

Hoover model 5906-900 spinscrub

Solution for Hoover SteamVac (F7452-900) brushes not spinning\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem shoul ... Hoover V1 SteamVac SpinScrub Vacuum

Lost manual for Hoover SteamVac Widepath 12 amp SpinScrub model F6030-900 series T120

... Vacuums

Brushes won't spin on a Hoover Steamvac SpinScrub Model F5918-900

Well the hand tool works off the suction of the machine and has nothing to do with the turbine that controls the brushes. if you can get the part i can walk you through taking it apart. when you write back, let me know what the model num of your mach ... Vacuums

Why is my hoover spinscrub 50 leaking tons of water while and after using model no. f5915905

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have lost my manual for my Hoover SpinScrub vacuum. Model f5914-900. is there a place to get one online

HiHere the manual:F5914900\015\012\011\011\011\011\011\011 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover SteamVac Spot/Deep Cleaner, model F5515. I've had it a little over 1 year. It will not extract dirty water from the floor. I've made sure the recovery tank is attached correctly and also that the stair tool is connected. Is there something else I can try??

... Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover spinscrub The used water tank on my Hoover steamvac spinscrub is empty but the ball keeps popping up as soon as I begin to try to use it. What's the problem?

... Vacuums

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and

The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover SpinScrub brushes not turning - Hoover V1 SteamVac SpinScrub Vacuum

Hi There,Here's a very helpful Tip that I've written that explains step by step how to diagnosis the Hoover SteamVac when the brushes stop spinning. This will also walk you through how to replace the brush gear turbine assembly if you f ... Hoover V1 SteamVac SpinScrub Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy

Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

Need a front wheel assembly for my Hoover Tempo model u5144-900. I see similar looking Hoover wheel assemblies online for different models, will they fit mine?

The Tempo series cleaners look similar, but are different colors. The wheel assemblies will work if they look identical in appearance to yours. ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0892 seconds