Having problems with your Hoover V1 SteamVac SpinScrub Vacuum ?

Hoover F7431900 I am using this for the first time in a little while and both tanks, the water tank and the cleaning tank are both leaking. Any help in this matter would be appreciated!

Answers :

The tank you are talking about has the soap container attched to the back of the water tank, then probably you need to replace the tank. If this has different tanks, then you may have to replave the seals that the tank sits on.
Repair Help & Product Troubleshooting for Hoover V1 SteamVac SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover F7431900 I am using this for the first time in a little while and both tanks, the water tank and the cleaning tank are both leaking. Any help in this matter would be appreciated!

The tank you are talking about has the soap container attched to the back of the water tank, then probably you need to replace the tank. If this has different tanks, then you may have to replave the seals that the tank sits on. ... Hoover V1 SteamVac SpinScrub Vacuum

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.

Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a hoover F5915-900. Today when I got it our to use it I noticed that it was leaking. I did some troubleshooting, but not sure where to go from here. The solution tank leaks out if the recovery tank is connected also. If I remove the recovery tank and leave the solution tank on it does not leak. Any suggestions would be appreciated.

It dont shamppoo my carpet dont come out or **** it up the hose for funture workes good no sham pooer for rugs ... Hoover F5915910 Upright Steam Cleaner

The Bissell Proheat 2X doesn't release the solution. I have cleaned everything I can see and understand there is a filter somewhere. Would like to know if that would even help... ANY OTHER SUGGESTIONS WOULD BE APPRECIATED! No men around just us girls and we have NO idea how to fix it!! Thanks-Cheri

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My hoover steamvac(purchased less than a year ago) leaks the dirty water. I checked the tank and nothing is broken/cracked. Im not sure how the water would be leaking. Please help!

... Hoover F5915910 Upright Steam Cleaner

Roomba 560 just goes in a small circle, will not go forward or backwards, then a red alert lights up ststing to clean it, which a throughly good cleaning has been done, gave this as a gift to someone and they only used it for a short time before this happened, any help to solve this would be appreciated

... iRobot Roomba 560 Robotic Vacuum

Vax carpet washer deluxe leaks from bottom of water tank, somewhere between coming out of the tank and going into the jet to squirt on the floor. pissing me off - any help would be great!

Just stripped VAX rapid carpet cleaner model v-025 down found out the internal plastic water valve keeps sticking in open position causing the water to free flow on the carpet when it should be closed pop the water flow regulator part out of housing ... Vacuums

Hi my beater bars will not turn anymore, i have tried to reset it cleaned the bars removed and cleaned the front wheel, but still they will not turn.Any help would be appreciated

Belt has probably broke in the power head ... Vacuums

Cleaning Filter Hi: I want to clean the filter on the B&D pet hepa vacuum, but can't figure out how to take it out of its housing. I can remove the housing from the actual vacuum, but don't know how to get the filter itself out. It sure does smell of dog, so any help would be appreciated.

... Black & Decker Black Decker Bagless Canister Pet VacVacuum

I have the Hoover max Extract 77 and when I'm cleaning the carpet, the clean water tank leaks on the floor, even if I'm not squeezing the trigger. The clean tank doesn't leak when I fill it, but once I place it where it fits and start using the vacuum, the clean water drains out on the floor. The dirty tank fills up, so the suction works, but, I don't know what is going on?

... Hoover Vacuums

I have an older kenmore canister powermate 3.9 and the vacuum itself works fine but the powermate isn't sucking after a toy was sucked up last week. The toy is out but the powermate doesn't work. I assuming that is what it is called. The big long part that hooks to the canister that actually cleans the carpet. I would appreciate any help.

... Kenmore 25512/ 25513 Progressive Canister Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated

1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Bissell Powersteamer 1695 The cleaning solution tank does not leak until I attach it to the machine. Then the solution pours out , looks like from the fittings where the liquid would go to be pumped out. I bought the used, I wonder if if could be needing a washer/gasket sort of thing?

Hi gownzilla,The solution cap has a spring loaded fitting so that when you put it in upside down, the projection in there in the machine pushes up on the fitting to release the solution when you pull the trigger. It could be that the proj ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Eureka/The Boss doesn't seem to have the suction power it had. However, when I place my hand under the hose, it has good suction, then when I try to pull in a small particle, it doesn't, unless I have the hose nozzle completely over the particle. The vac is 10 yrs. old. I cleaned everything. Someone said the belt. Would the belt matter if the hose doesn't **** well? It is just old and worn out? It did shut off recently do to overheating. Help. Thanks. Lorraine

Doesn't "The Boss" Vacuum have a filter? Perhaps your filter is clogged and not allowing it to work properly. ... Vacuums

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey

... Vacuums

I know this sounds like a dumb problem to have for a vacuum but our 6 year old dyson has so much suction you can't move it across the floor. It only recently started doing this and I haven't done anything to it such as clean the filters in over 6 months. Any help would be appreciated

... Dyson DC14 Telescope Reach All Floors Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet

Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/

3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.

The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bex Bissell Proheat carpet cleaner refuses to spray water from the lower jets and it is intermittant from the wand. I have cleaned the jets to no avail. Any help would be appreciated. Thanks

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha

You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have the Electrolux Velocity Pet Lover 1800w which has lost all suction from the pipe. I have checked for blockages and cleaned the filter but still no joy. Would changing the HEPA filter resolve the problem? Your help is much appreciated

... Vacuums

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0732 seconds