Having problems with your Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum ?

How to tighten or replace roller belt on hoover

\015 How to tighten or replace roller belt on hoover windtunnel 2\015

Answers :

Repair Help & Product Troubleshooting for Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to tighten or replace roller belt on hoover


... Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

Belts Burning On our Ultimate G, belts are lasting about 2 uses and they smell and burn off. I am looking at the roller and I can see a slight grove where the belt rides. Is it time for a new roller. I am sick and tired of replacing belts and smelling up the house. Thanks Dusty


Yes, replace the brush roll, the ends or end is probably bad and causing the belt to slip and burn up. ... Kirby Ultimate G Bagged Upright Vacuum

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.


Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

My vacume is less than 6 months old. I've gone through & replaced 4 belts. Now I realize the roller is not rolling which is causing the belts to break. The roller is free of all hair and debree. What should I do to fit the roller?


Very strong chance the end caps, made out of rubber could be a manufacturer defect. Many parts on vacs are made by different sources. ... Bissell Vacuums

Replace belt on fantom cyclone vacuum? the manual does not decribe replacing the roller belt - i can't get it open to expose the belt


On my 10-year-old model, the two screws securing the cover are under the two llight bulbs. Pry off the clear plastic covers, take out the bulbs and screws, and the cover lifts off. ... Fantom Vacums Cyclone XT Upright Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?


... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

I have a GE 106766 Canister Vacuum. The belt on the power end stretched and I replaced it. Now the roller froze up and won't move. Where can I find a replacement roller?


Try this sitehttp://www.onlinevacuumparts.com/ps-328-7-ge-6850-106766-canister-power-nozzle-parts.aspx ... GE 106766 Bagged Canister Vacuum

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

How do I replace the belt on a Bissel Powerlifter rug shampooer? I have removed the door that is marked "access belts". The problem is that I don't see how to get the belt around the lower roller. There is no problem getting the belt around the upper prong. Please advise.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.


The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Oreck xl making whinning noise after replacing motor,belt and brush roller..


... Oreck XL Ultra Bagged Upright Vacuum

HOW DO I REPLACE THE TOOTHED BRUSH ROLLER BELT ON MY PRO 8910


Here is the Instruction or User Manual for the 7910 and the 8910 series machinesand this link is video how to change both ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0562 seconds