Having problems with your Hoover V2 U8140-900 WindTunnel Upright Vacuum ?

The Rotary brushes do not rotate/spin when the unit is turned on.

\015 Hoover Windtunnel V2 12 AMP, Bagless, Model U8140-900\015

Answers :

Check the belt it may be stretched or broken...also carpet and hair or other debris around the bruches may have it in a bind,,..remove the 2 screws holding the bottom on to check this
Repair Help & Product Troubleshooting for Hoover V2 U8140-900 WindTunnel Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The Rotary brushes do not rotate/spin when the unit is turned on.


Check the belt it may be stretched or broken...also carpet and hair or other debris around the bruches may have it in a bind,,..remove the 2 screws holding the bottom on to check this ... Hoover V2 U8140-900 WindTunnel Upright Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.


That's the way it's supposed to work. ... Vacuums

Roomba 500 Unit comes on and moves, but brushes don't seem to be turning. Unit stops and then says, "please clean brushes".


Roomba 500 Series have a serious problem with hair and other fibers working their way into the drive gears. The resulting resistance in the drivetrain is interpreted by the machine as overloaded brushes. People who experience this problem should co ... Roomba Robotic Floor Bagless Vacuum

NOTHING WORKS Used the unit 3 1/2 weeks ago, now it will not do anything except turn on. The water and shampoo will not dispense and the brushes will not turn. Is there some type of reset button that can be utilized????????? Have had unit for several years with only one other problem, the soap dispenser had to be replaced because it leaked. Teresa


Check the foam filter on the underside of the recovery tank lid, make sure that it has at least a 1/4 in. gap from the top. There also is a filter, from the bottom, it has a red frame, pull out far enough to clean it.\015\012On the bottom of t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I followed the instructions above and found that neither brush turned. when no brushes are in and the vacum is running the gears are not turning either when i look inside the unit


You need to clean the gears hidden in the housing itself. they have become clogged with hair etc and wont turn.This will require you to remove the housing. ... iRobot Roomba 530 Robotic Vacuum

Vacuum cleaner when we turn the unit on the spinner brush does not turn the belt is still on the brush but how do you get to the other end.


Go to thehooverstore online. here you'll find an exploded diagram of your machine and how the belt is installed. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

The brushes will not turn. How do I open the unit to put the belt back on?


Hoover doesn't use belts on their steam cleaners. Either the shaft that is on top of the brush block broke off, or the turbine is bad. The turbine is what turns the brushs. ... Hoover F7220900 SteamVac V2 Upright Vacuum

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

My Bissell Proheat 2X brushes are not turning. I have narrowed the problem down to either the brush motor or the circuit breaker How do I determine which unit is at fault?


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a one year old Beam central vac. It has supervalves. The handle (connected to the hose stopped turning on the unit. The handle still powers the brush but no longer turns on the suction?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566201 ... Vacuums

The brushes do not turn when the unit is on. What do I do? The belts appear to be fine, Is there an internal fuse?


Check belt if ok .may be brushes motor bad.... ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Brush does not turn. suction with the handheld unit it fine but when used as a floor sweeper it hardly picks up anything


These stick mmachines do not have a tremendous amout of suction at the best of times but if it has a full bag, or full dirt container, or dirty exhaust fiters it will take away from the air flow as well. take a flashlight and look up in to the tube o ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

The Rotary Brushes do not spin.


That model has a direct drive brushroll motor and transmission. the brushroll motor is most likely bad test it with a continuity tester if it tests open or high resistance than its bad ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

The rotary brushes on my Windtunnel V2 won't spin. I wasn't having any problems just, boom, no more spinning. I've had to clean hair and other stuff from them in the past. At that time, they wanted to move and couldn't. Now, I turn the machine on, and they don't move but make a loud noise. What do I need to do?


... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

I have model Model # 11635923500 Sears Kenmore--the unit runs but the brush does not turn--do I need circuit board or wiring ?


... Kenmore Vacuums

I have a kenmore progressive 359235 vacuum with intelliclean. Has been great for about 3 years but now the brush bar has stopped turning. This is a direct drive unit with a circiut breaker reset button on top . The button is not tripped. Any ideas ?


... Kenmore Vacuums

Light burned out and at same time sucking motor stopped working. Brushs still turns. is there as fuse I can change out or is the motor toast ? this unit is less then a year old


Contact your local warranty center they have had problems with that model ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The rotary spin brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt either came off or broke ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.


... Electrolux Vacuums

Brushes still wont turn


I had same problem and it was the turbine assembly. Part was only $28 but with labor it cost me $140 total. Plus it took over 5 weeks for my vacuum repair shop to get the part. In hindsight, I would have just spent another $100-$150 dollars and bo ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Hoover WindTunnel, month-old belt, now too large to turn brush


I suspect you have been bitten by the Chinese bug.\015\012\015\012A very large percentage of replacement parts for all manner of appliances and vehicles are now being conterfeited in China who we should know by now has no respect for the intell ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.


... Euro-Pro S3325 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0717 seconds