Having problems with your Hoover Vacuum. SteamVac Spin Scrub Extractor F5915100 ?

I have a Hover F5915100 the spinScub will not turn

\015 Spin Scub will not turn\015

Answers :

This video will show you the problem and how to fix
Repair Help & Product Troubleshooting for Hoover Vacuum. SteamVac Spin Scrub Extractor F5915100

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hover F5915100 the spinScub will not turn


This video will show you the problem and how to fix ... Hoover Vacuum. SteamVac Spin Scrub Extractor F5915100

Hover windtunnel It will start when you plug it in and wont turn off with the switch you have to plug it in and unplug it to get it to work.


I had the same problem with the Hover windtunnel. All I had to do was remove the two screws holding on the handle and then pull the handle off pulling horizontal to the ground. Then I manually turned to swith off. Check it to make sure the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hover f7458-400 carpet cleaner brushes wont turn


Based on the hints above I cleaned the filter as it was clogged. That did not fix it. Then I took a stout screw driver and used it to turn the square brush drive, The drive broke loose and I am in operation with no dis-assembly. Hooray! ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Brushes wont turn on model number f5915100 Hoover shampooer


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Roller will not turn on hover u57809rm - Hoover Vacuums


One of the two belts may be broken or stretched on the unit. USUALLY it is the thin flat belt that runs directly off of the motor assembly. Replace the belt on the unit and you should be good. ... Hoover Vacuums

The brushes will not turn. How do I open the unit to put the belt back on?


Hoover doesn't use belts on their steam cleaners. Either the shaft that is on top of the brush block broke off, or the turbine is bad. The turbine is what turns the brushs. ... Hoover F7220900 SteamVac V2 Upright Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

The brushes on the Hoover All Terrain Steamvac won't turn. However, when I try to turn them manually they will turn. So, why won't they turn when the machine is turned on?


Some vaccums have a belt on the brushes. might need a new one if it does have the belt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have an electrolux Enviro multi steamer which I was using this morning. I turned the steamer off for approximately 1 1/2 to do some shopping, and when I turned it on again, the steamer light turned on (green light) and then I waited for the orange light to go on, which too a while. When the orange light does turn on, there is no steam when you press the yellow button on the handle. I have checked for water, and the steamer is full, I have turned it on and off several times just in case that wi


Problem fixed itself. Turned off for couple of hours so unit can cool down completely and when I turned it back on it started working again. ... Vacuums

Turns on when I turn the switch all the way off and then back on but when it shuts down it will not turn itself on automatically it will draw water out of the air but only if i turn it on manually.


Your question cannot be answered without more information.\015\012\015\012What kind of vac are you talking about to begin with? ... Vacuums

My Dyson DC07 will not turn on. I was just using it and moved to a new area and plugged it in and it turned on for a split second and then it turned off and now it won't turn on at all. Any suggestions?


Loose wire, bad switch, or thermal cut-out. In any event, you will have to use a voltmeter to troubleshoot the problem, there is no way of knowing the problem otherwise ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda


You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

During the winter i turn the dehumidifier off. but when i turned it back onthis spring because you can feel the dampness in basement, it turns on but it does not absorb any water. i cleaned filter??? it turns on and sounds normal but it isn't taking any water in??? help


Turn the machine on maximum and let it run for an hour or so. Then check the coils in the back with your hand. If they are not getting cold at all, then there is a significant problem with the refrigeration process in the unit. It may have developed ... Vacuums

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.


Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.


If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

I saw your response to the Tork 1101 timer posting. Could you make a guess on my problem? It runs fine for turning on and turning off the downrange lights. But when it turns off the downrange lights the timer itself turns off. The clock stops.


... Vacuums

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a


Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e


The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.


The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0526 seconds