Having problems with your Hoover Vacuums ?

Reassembly of brush roll bearing/washers on Hoover Runabout

\015 I dis-assembed the brush roll to remove all the hair wrapped around the bearings under the end-caps. Now,Which direction do I re-install those bent ''springy'' washers that go underneath the brush roll bearings? (the sharp edges toward the plastic brush roll or towards the metal bearing? \015\012\015\012Or does it not matter?\015

Answers :

It will make no difference which direction those washers are installed, just that they are installed.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Reassembly of brush roll bearing/washers on Hoover Runabout

It will make no difference which direction those washers are installed, just that they are installed. ... Hoover Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.

Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

Hoover WindTunnel U6433-900 brush roll control broken off

... Vacuums

Hoover windtunnel Self-propelled - brush roll stops

There is a idler wheel that will drive the V belt, sometimes they jam and you just have to reach in, push and make sure if comes in contact with the belt. Alot of times tho it is the other flat belt, 38528035 that will stretch and can cause you to h ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover U6434-900 Brush roll not spinning, has new belt.

I took the top of the vacuum apart and found the cable that drives the wheels was broken. I am going to order a new cable. ... Hoover U6434-900 Bagged Upright Vacuum

Brush roller on Hoover runabout won't spin - Hoover Vacuums

... Hoover Vacuums

Hoover u6485900 brush roll will not turn

... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My hoover carpet cleaner's brushes dont roll, it is a steam vav power max

They may not be "stapped" in postion correctly. Do you have the manual?\015\012If not go to: www.hoover.com for a free copy. ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

I purchased a hoover wind tunnel SH40050 and am not able to get the brush to roll

Just check the belt flip the vacuum over take lid off and check belt ... Hoover Vacuums

I have a Hoover Linx cordless vacuum stick and it is not picking up anything. The motor works, the brush rolls but it spits out dirt instead of sucking it up.

... Hoover Platinum LiNX Cordless Stick Vacuum

Hoover wind tunnel self propelled brush roll not working

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover windtunnel with a bag automatic brush roll not working

... Hoover Vacuums

My Hoover U6434 makes a knocking sound when I turn if off and it powers down. The belts and brush roll are fine. Any idea's? Thank you, mpipes

Its probobly a pice of dirt being slung around on some hair or thread. try cleaning the fan and look carfuly for hair tightly raped around the shaft. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush roll not working on hoover upright U6455-900

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=700283\015\012Generic problem for all Vacuums\015\012Brush roll not working on\015\012Posted by archies ... Vacuums

Hoover Mach 6 stopped running and won't start up. Cleaned the brushes(roll freely) and checked for a clog but couldn't find any.

Ya okay how do you get to the motor. Then when you get to the motor are you soppose to guess what is wrong with it by just looking at it.. What kind of solution did you give this person? I'd say not a very good one. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Hoover tempo It will still **** through the hose but not from the brush-bottom. Can't find a reset button. Vacuum was GREAT and is only about three weeks old. I know it still works because it has plenty of strength through hose, but won't pick up when rolled across floor. thanks! Marian

Sounds like a blockage or belt off in the foot of the vacuum. there is no reset button on this model. ... Hoover Tempo Widepath Upright Vacuum - Blue

My hoover widepath tempo does not pick up, the brush roller doesn't roll and it's harder to push

Ya, you need to replace your belt. You can get this belt here:Hoover Widepath Tempo Belt ... Hoover Tempo Widepath Upright Vacuum - Blue

Brush roller on Hoover upright stops turning

There should be a belt tensioner for the V belt, maybe it is not contacting the belt when you tilt the handle back. If this is less then 1 year old, then it is under warranty, take it in to a warranty servicer for warranty repair. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.

... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne

... Hoover S3614 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0538 seconds