Having problems with your Hoover Vacuums ?

My hoover windtunnel will not turn on. - Hoover Vacuums


Answers :

The motor is probably burnt out.have it checked at a vacuum store.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush on my Hoover Windtunnel T series won't turn when I'm vacuuming carpet. It does, however, turn when I'm vacuuming bare floor, and I didn't think it was supposed to do that.


1) test the belt +brush for worn and replace2) test the motor God bless you ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Windtunnel vacuum brush won't turn - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Hoover windtunnel t series vacuum won't turn on. power source has been checked so it's something with the vacuum


... Hoover Vacuums

Wind tunnel t series vacuum won't turn on - Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107


I had the same problem and used a tool to clean out the suction tube on my Windtunnel Series T. It was full of junk packed in tight. After cleaning it out there's no more turning off or overheating. It actually works better than when I first got it ( ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

Hoover uh30010 won't turn on - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

My hoover windtunnel will not turn on. - Hoover Vacuums


The motor is probably burnt out.have it checked at a vacuum store. ... Hoover Vacuums

My vacuum died. It won't turn on. It is not the outlet. Is it a blown fuse? How do I replace the fuse? Where does it go? This vacuum is a little over 2 years old. My older Hoover WindTunnel STILL works and has never had this problem.


It's probably the power switch. My switch was dicey for a couple years, finally gave out. Easy to replace.\015\012\015\012Remove the two screws just above the WARNING on the rear of the upper handle assembly, then slide the whole assemb ... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Vacuum will not turn off - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


(1) Please check the four screws that mount the upper handle to the lower handle. If they are not tight, the actuation of the switch may not be adequate.\015\012\015\012(2) Remove the four screws and the upper handle. you will see the r ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush does not turn because belt is loose - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


You need a new belt that isn't stretched. You can get a replacement here:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush wont turn u6485900 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Here is manual > http://hoover.com/file/509/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Agitators do not turn? - Hoover V2 U8140-900 WindTunnel Upright Vacuum


... Hoover V2 U8140-900 WindTunnel Upright Vacuum

Bristle motor will not turn - Hoover WindTunnel V2 U8148-900 Upright Vacuum


Its shot ... Hoover WindTunnel V2 U8148-900 Upright Vacuum

Roller brush does not turn - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


The drive belt is worn. you can get the replacement belt here:http://vacbelts.com/hoover-windtunnel-38528-035-belt.htm ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Suction will not turn on - Hoover S3755 WindTunnel Bagless Canister Vacuum


Might be the switch is faulty or the vacuum motor is not being activated or the motor by itself is defective.\012You might have eto take a look through the wiring to confirm if the volatge flows from the switch to the motor. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover windtunnel vacuum roller brush doesn't turn. Have removed hair and lubed and belt looks ok. Any ideas?


Does the motor turn?  if it does replace the belt. ... Hoover Vacuums

Hoover canister vacuum (windtunnel)- turned it on and it had good suction, then smoke came out and it smells like something is burning. Is it the motor burning up or something else?


Probably the belt..\015\012Turn it over so the bottom is facing up..\015\012Remove the plate that surounds the brush..\015\012Check to se if brush is spinning frely and that the belt is on there poroper ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush motor does not turn on - Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum


You could check Sears.com and click on parts then type in Model # or Part # this will get you a parts list you can choose from. ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Drive belt won't turn - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Hi try w,d 4o spray on wheels each side ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover UH70600 Windtunnel Max Multi-Cyclonic Bagless Upright Vacuum Brush won't turn after cleaning out debris, belt is fine.


... Hoover UH70600 Windtunnel Max Multi-Cyclonic Bagless Upright Vacuum, 7 Floor Settings, 15 Inch Cleaning Path, 28 Foot Cord Rewind, On Board Tools
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0835 seconds