Having problems with your Hoover Vacuums ?

On a Hoover Dimension, frozen impeller

\015 On a Hoover Dimension, the plastic impeller has fused itself against housing. I have broken it free but it is still pretty tight against the housing\015

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On a Hoover Dimension, frozen impeller


... Hoover Vacuums

Hoover Elite II Model # u4689-910 Impeller replacement


I have had to use a dremmel tool to cut the plastic around the shaft, you can also something sharp and a hammer to break away the remainer of the fan. There are no threads on the fan so to keep truning it may or may not get it off. Just have to wat ... Vacuums

Change impeller on hoover upright - Hoover Commercial C1403 Bagged Upright Vacuum


... Hoover Commercial C1403 Bagged Upright Vacuum

Hoover dimension 1000


There are a few screws on the bottom of your hoover, remove them using a suitable unarmed and then pulling firmly upward. ... Hoover S1361 Bagged Canister Vacuum

Hoover U4395 Vacuum fan (impeller) broke


I've done these impeller replacements on two different Hoover convertibles.Yes it's a left handed thread on all classic convertibles - loosen it clockwise (reverse thread)After getting married, my wife upgraded the vacuum to one of th ... Hoover Vacuums

Same problem my vacuum cleaner is Hoover Dimension 1000


Witch model due you have ? ... Vacuums

How to open and change bag on Hoover dimension 1000


... Dimensions Vacuums

Hoover Dimension has no suction and it smells of something burning


Pets in house? check all hose passages for "hairball" clog...and check the drivebelt that spins the brush...(some have an electric motor to spin the brush, thus no belt) ... Hoover Bag Paper Microfilter Dimension Upright 3 Pack

Change vacuum belt on hoover dimension U5209


... Vacuums

Hi, the seal from the impeller and pump shaft leaked. got new seal kit and installed. only disconnected the contacts piece to get clean attachment to shaft and the points now stay together looking like the springs are frozen thanks for your help


Hi ggetman38...\015\012\015\012That is normal\015\012What you are talking about is the centrifugal switch, they will swing apart when the motor rotates, they are there to start the motor with the points touching each other at motor ... Vacuums

How do I get at the cord rewinder for a hoover dimension 1000


... Hoover S3639 WindTunnel Bagged Canister Vacuum

How to replace fan impeller on old Hoover upright. Taking off the belt pulley is giving me the problem.


Depends on how old it is ... if it is real old try putting a open end wrench on metal belt pully, and then hit wrench with a hammer i think counter clockwise to loosen ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover dimension 1000 dead after hot - Vacuums


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=557355\015\012Generic problem for all Vacuums\015\012Hoover Dimension 1000 dead after\015\012Posted ... Vacuums

How to change power cord of hoover dimension 1000


... Hoover Vacuums

Belt Replacement How do you change/replace the belt on a Hoover Dimension Supreme vacuum?


Take the bottom plate off, the brush roll and belt are there. the belt goes around the brush roll and hooks to the motor shaft. If you can't get to the motor shaft, then you will nee to remove the top cover also. ... Vacuums

Removing the pulley from the shaft on a hoover c1433 to replace the fan or impeller.


Removal of the pulley requires extreme care. There is a small opening on the side of the black motor housing to allow a special tool (or a screwdriver) to fit on a slot on the armature to keep it from rotating while the pulley is unscrewed. You MUS ... Hoover Commercial Guardsman C1433 Upright Vacuum

I need to replace the belt on the power nozzle of my Hoover Dimension 1000 Model S3491. Unfortunately, I have no written instructions on how to do so. I purchased the vacuum cleaner in the mid-80s. Are the instructions still available? Thanks in advance.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566792\015\012Generic problem for all Vacuums\015\012I need to replace the\015\012posted by Deb in Iowa ... Vacuums

How do I install the belt in a Hoover dimension II vaccuum?


Take off the bottom plate, then you can get to the brush roll and the belt. The belt goes around the brush roll and goes to the motor shaft. If you can't see the motor shaft, then you will have to take the top cover off to get to it. ... Hoover Vacuums

HOOVER Dimension Vacuum Model U5209-930 Manual


... Vacuums

No suction on my Hoover Dimension


If you smell something burning unplug until problem is found and fixed, suspect if no suction hose is blocked and if brush wheel it or the belt may be causing the smell, a bad or failing motor is less likely but possible. ... Vacuums

Hoover Dimension Vacuum - No suction - Any suggestions?


Your fan broke. This is a direct air motor, which means what you pick up goes directly through the fan and they break if you pick up something too big. It's an older design and fortunately one that is made to be repaired. The Fan Part # is 38755030. ... Hoover U5227-930 Elite Upright Vacuum

I have a Hoover cannister vacumn cleaner Dimension 1000 Serial number 0040229 and model number S3283 How do I open it to put in a new bag?


... Vacuums

New Hoover Dimension Supreme vacum belt can't be installed. No


... Hoover U5227-930 Elite Upright Vacuum

Hoover Dimension 1000 quadraflex - Vacuums


... Vacuums

Hoover Model S3281, disassembly instructions


GET TO THE REEL AS FOLLOWS:\015\012 \015\012(BEFORE YOU START, BE SURE TO UNPLUG THE DIMENSION FROM THE OUTLET)\015\012 \015\0121). TURN VACUUM OVER ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0453 seconds