Having problems with your Hoover Vacuums ?

I have the hoover nano-lite and today when I put it on the carpet it is very hard to push. I never had that problem before.

Answers :

You didnt set it to the right hight adjustment
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the hoover nano-lite and today when I put it on the carpet it is very hard to push. I never had that problem before.

You didnt set it to the right hight adjustment ... Hoover Vacuums

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor

On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My hoover widepath tempo pushes easy in any hight when off, but turn in on and you can hardly push in forward. I took the beater bar off and cleaned everything and still having this problem

Make sure the beater bar is turning sometimes it will freeze up with dust and dirt will get inside the bearing caps on the end of the brush ... Vacuums

I have a windtunnel upright self-propelled that is very difficult to push, on carpet or hard floors. Seeems that it is stuck to the floor and at times you can smell the rubber from the belts. What could be the problem or problems?

Raise the front. you are trying too hard ... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe

I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Our Hoover windtunnel V-2 upright is Very hard to push I never use it because of this. Is this normal or could something be wrong?

... Hoover Vacuums

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu

Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush won't engage on my hoover windtunnel vacuum. I see the problem is that the "carpet / hard floor" slide bar is broken / jammed. How do I access the slide bars from below to unjam them?

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I've had my Kenmore Progressive canister for at least several years and never had a problem. Now, the carpet head brush does not rotate, it's not getting the connection unless I push down maintaining pressure on the handle.

Hi, try pushing the reset button with a pen or paper clip. If that doesn't work, the motor may need to replaced. If the reset button is stuck, if the reset button is stuck, use a pair of tweezers to pull it back out......\01 ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson suddenly hard to push on carpet

I know this sounds silly, but it works. Turn it over and wipe all the black residue off the bottom of it (off the plastic on the bottom that rubs on the carpet as you push and pull it). I thought my husband was out of his mind when he told me that ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dyson vacumn is hard to push on carpeting. How do i fix it?

This happens when the bristles in the brush roll get worn down too short. Put in a new brush roll and the machine will pull itself over the carpet, so you hardly have to push at all. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.

Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks

HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Oreck XL 7000 is hard to push through a modest pile carpet. They gave us a shag attachment but all that does is push the carpet down. It is not ususable for us with bad backs etc.

... Oreck XL2200 Bagged Upright Vacuum

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]

Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Hoover Windtunnel My Hoover is about a year old and now it's not as easy to push, when I first bought it, it would almost glide over the carpet, now it can be a bit of a struggle to push it around. Any ideas why?

The gears inside might be worn down. ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

I have the hoover automatic dual vac 5. this is the 3rd hoover rug cleaner i purchased and always the same problem the spray underneth the rotator bars hardly dispenses and the floor hardly gets wet, this has happened with all 3 rug cleaners

The carpet is not intended to get soaked, like what you see with a spray application. If you are seeing a stream of water in the nozzle/tank during the recovery stroke, this is working properly. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Hoover Windtunnel carpet level adjustment

The suction is so great that it sucks up your carpet, then nothing works. I get my children to stand on the corners/edges of the rug so that it stays perfectly flat on the floor while I vacuum. Or, you can turn off the brush roller (set it to "har ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.

I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.

I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?

Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1124 seconds