Having problems with your Hoover Vacuums ?

Brush will not run - Hoover Vacuums

Answers :

The reason your brush wont turn is because the belt has either broken or stretched. If you replace the belt it should solve the problem. You can find hoover replacement belts at either www.hooverbelts.com or www.vacbelts.com.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.

Has this not got a rubber belt drive? ... Vacuums

Hoover Savvy Brush only runs when the vacuum is moved backwards

Replacing the entire upper handle assembly with OEM Part #48663238 will solve your issues, for a cost of about $35 plus shipping. ... Hoover U8185-900 Upright Vacuum

Brush will not run - Hoover Vacuums

The reason your brush wont turn is because the belt has either broken or stretched. If you replace the belt it should solve the problem. You can find hoover replacement belts at either ... Hoover Vacuums

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work

If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.

Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums

My hoover Savvy vacuum is no longer sucking up dirt- brush turns

... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.

Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

The brush on my Hoover Windtunnel T series won't turn when I'm vacuuming carpet. It does, however, turn when I'm vacuuming bare floor, and I didn't think it was supposed to do that.

1) test the belt +brush for worn and replace2) test the motor God bless you ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover, model # UH30070 Wind tunnel vacuum Brush won't turn. I do not see how to remove this to replace the brush, and besides it's only about a year old! Why is it already broken? There's no visible evidence on the brush that would make it stop, i.e. string, clogged, etc. Can you help?

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.

Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

I need to know how to replace a agitator brush for a Hoover Fusion model U5180 900. I was given the vacuum, but without the manuals, so I have no instruction on how to replace the brush. I have already purchased the new brush. Thank you for your help

Please use the following link.\015\012http://www.hoover.com/pdfs/manuals/U5180900.pdf ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Need Hoover cannister vacuum floor brush & filter bags

Yes attachment are available just bring your wand into your local vacuum store to insure the proper fit ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0859 seconds