Having problems with your Hoover Vacuums ?

Self propulsion doesn't work on my upright. Vacuum works fine otherwise


Answers :

If the model you have is a Hoover windtunnel self-propelled model then you need this belt:

http://www.vacbelts.com/hoover-windtunnel-38528-035-belt.htm
I do not know what Hoover model you have but most are equipped with two belts. The main belt runs the brush. The secondary belt is for the self propel mechanism. To replace this secondary drive belt you need to remove the primary belt. This is because the secondary drive belt runs inside the primary belt and can only really be seen clearly once it's removed.

If you have any trouble locating and or removing it please respond back and include the model # of your vacuum.
Hope this helps.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Self propulsion doesn't work on my upright. Vacuum works fine otherwise


If the model you have is a Hoover windtunnel self-propelled model then you need this belt:http://www.vacbelts.com/hoover-windtunnel-385 ... Hoover Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!


These belts need to be changed every 6 months regardless of the way they look. ... Vacuums

Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.


Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.


Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Vacuum works fine when using the attachments, but as soon as we try to use it in it's normal upright position it does not work. We have cleaned all filters and removed debris from roller, but nothing has helped.


Greetings,\015\012\015\012There could be a few things that would cause your Dyson to do this. I will give you detailed step by step instructions along with pictures on how you can diagnose this problem. \015\012\015\012Po ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Vacuum head stopped working, unresponsive to on/off switch and light bulb is out. Canister otherwise works fine. Help!>?


Power head on/off switch could be faulty, Wires running through hose may be broken, electrical connections may be burnt.Motor in Powerhead could be dead. ... Vacuums

Upright self propelled Windtunnel model: The self propulsion does not work and I can see why. I need to know how to get the top cover off the machine to get to the broken part that engages and disengages the wheels. Can you tell me how to get the cover off?


Turn the machine upside down and locate about half a dozen recessed screws which hold the bottom and the top of the machine together. ... Hoover Vacuums

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.


Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

It will not suck up materials on the vacuum part. the hose works just fine when it remains plugged in to the upright part


Hi pop into bissel web page faq page type you querry see if there an answer http://bissell.com/Search/FAQ.aspriz. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Belt works fine but there is no suction - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


This usually indicates a clog in the hose and airflow system. It's most likely to be behind the filter in the tank or in the power head area.\015\012Detach hose from power head and look inside. If you can't see anything, try dropping a penny ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!


The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I just bought a Dirt Devil 12 Amp upright vacuum which seems to work fine but it is blowing out air in the front just under the filter housing. I see there is a vent there but should there be any air coming out during normal use? Thanks Brandon Smith


Yes. For the unit to be able to take air in from use it has to exhaust air. This is normal. ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

Hello :) My bissell proheat upright steam cleaner is not shooting any water out at the bottom and I was wondering what could be wrong. The handheld part is working fine, its only the vacuum part thats not squirting out any water.


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My oreck xl 3800 H2 upright vacuum cleaner does not turn on. It worked fine the last time I used it. Is there some sort of fuse that may have burned out?


Usually no fuse on these.\015\012\015\012Assume the outlet has been checked?\015\012\015\012I'd look at the on/off switch (that is a 2 speed unit, tight?) or the diode the gives the 2-speed choice, or the power cord as my firs ... Oreck Vacuums

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?


You have the answer and just don't know it. You are there so keep looking. Somewhere between where the suction hose connects with the lower hose and the power-head. There is a blockage, you may need to turn the unit upside down and look there or try ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1223 seconds