Having problems with your Hoover Vacuums ?

Hoover cleaner F72229RM, the brushes will not turn when operating it

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover cleaner F72229RM, the brushes will not turn when operating it

... Hoover Vacuums

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.

... Vacuums


Belt probably broken. unplug from power and remove the plate from the bottom of cleaner.belt should be visible on one side or other. ... Hoover F5891-900 Steam Cleaner

HOOVER Cleaner F5857-011 BRUSH'N'WASH Problem: Brushes not turning under load. Will turn slowly when raised from floor/carpet but can be held still by light hand pressure. Checked listed possible causes as per handbook but still not working.

... Hoover Vacuums

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.

Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.

You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes won't turn on my Hoover Steam Vac Cleaner. I have removed them and cleaned them and put them back in and they still won't turn. Any suggestions?

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover max extract brushes not turning - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.

... Hoover F5826-900 SteamVac Upright Wet Washer

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?

If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover WHS2001 2000W Bagless Pet Upright Vacuum Cleaner brushes won't turn even by hand, just delivered new but no instructions

... Hoover Vacuums

Brushes will not turn on my Hoover f7220-900 carpet cleaner

... Hoover F7220900 SteamVac V2 Upright Vacuum

Brushes wont turn and wont spray water - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes do not turn - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Check the brush block to see if the shaft that goes into the turbine broke off, replace brush block if it did. If ok, then the turbine may be clogged up, either clean it out or replace the turbine. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Hoover SteamVac F5914-900 that I purchased approx 6 mos ago. It just started having the following problem. When I turn the cleaner on there is a sudden burst of solution/foam that emits out to both sides from behind the brushes. How can I fix this??

Mine has been doing that occasionally, and I have ordered the pump assembly, #H43582003 which several have suggested is where the problem is. This leak, along with loss of solution going to the hand tool, seems to indicate that the pump is not workin ... Hoover V1 SteamVac SpinScrub Vacuum

My hoover savvy vacuum cleaner brush will not turn but the belt is fine. i was vacuuming and smelled a burned odor and thought the belt, but not. what's wrong

It could be the motor on it`s way out ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow

The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]

Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

Hoover steam cleaner spin scrub brushes wont turn cant find belt

I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a hoover carpet cleaner with the 6 brushes and they have stopped turning i have cleaned the little screen and still no results what may be the problem

I found a copy of the manual on the inter net and was looking through it and it told me how to takemy brush assembly out, so i did that and replaced my brush assembly. it was really easy and only cost 25.00. thanks for the help\015\012 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

The brushes on my hoover f7411-900 carpet cleaner will not turn. any ideas? thanks, Hank

The most common reason for this is that the air driven turbine that turns the brush has seized up. To test it, remove the brush and insert a flat screwdriver into the square hole that the pin on the brush normally fits into. If you can't turn the fit ... Hoover Vacuums

I have a Hoover SteamVac Duo Deep Cleaner, model #F5520. The brushes won't turn and it won't release solution. There IS suction. Any ideas what could be the problem?

... Hoover F5520 SteamVac Duo Upright Wet Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0890 seconds