Having problems with your Hoover Vacuums ?

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

Answers :

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding the guard cover over the beater bar). The belt is about $3 (part number 38528040). Take out the beater bar and put the new belt around it. Then put the other end around the metal bar and stretch the belt taut as you position the beater bar back into its channel slots. Replace the guard and top cover and you should be good to go...
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

I have an Oreck canister vacuum, it says fc1000 on the bottom sticker, it's red. My problem is that the suction in it works perfectly, the belt is ok, and the roller can turn, but the motor doesnt turn it when I turn on the power.

... Vacuums

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........

Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port. ... Hoover Tempo Widepath Upright Vacuum - Blue

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

When I turn the vacuum on, and let go of the button, the vacuum just immediately turns itself off again. I have checked the cylinder and the hose and there doesnt appear to be any blockages. Can you please help?

Hi there, \012The problem is the switch itself. It is just a really common ailment for the Dyson DC08. I h ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I got a plastic bag caught in the DC17 Dyson Vacuum. It will not turn now. I do not think it is the belt, as it is there and not broken. The belt and/or the roller is not turning

You need to remove the plastic bag.thats stopping everything ... Vacuums

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]

You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?

It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

The vacuum sucks but the roller won't turn. The green light won't come on. The screws on the back are too tight to turn. We think it's the belt but are not sure. Can you verify? Thanks

... Sebo Felix Classic Bagged Upright Vacuum

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.

This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?

Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

Dyson i got a free dc07 animal but the brush doesnt turn it appears the belt is still on it but i cant see how to get at the belt

Hi.\015\012\015\012There are 2 belts the one is hidden under the Black casing.\015\012\015\012If you require help got to this site http://dysonmanu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Is there something on the shaft that will not allow the belt to turn? Our vacuum the roller will not turn.

It could just be the belt. If the belt is worn or stretched It will not turn the roller brush. You can get replacement belts here:Dyson DC07 Replacement ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?

Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My hoover u8130-900 roller brush won't turn. It does't appear to have a belt. What could it be? If it does have a belt, I can't find it and the manual doesn't mention it.

... Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

After vacuuming over a thick strand of loose carpert my brush roller will not turn on its own. The piece of carpet was removed easily and the belt is not broken. Your assistance would be helpful. Thanks

Make sure you can spin the brush by hand. The belt got hot and glazed when the carpet was stuck and will need replaced. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Replaced belt but isn't tight to turn roller - Eureka Smartvac 4870 Bagged Upright Vacuum

Are you sure that you have the right replacement belt? Here is a link to the belt you should have and the manual:Eureka 4870 Belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1368 seconds