Having problems with your Hoover Vacuums ?

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!


Answers :

Hello,

You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself.

Hope this helps.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!


Hello,You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself. ... Hoover Vacuums

I have a Kirby G5 vacuum that when light pressure is put on the handle it moves forward but in a jerky movement. Like the drive is engaging and disengaging. If you keep forward pressure on the handle the jerkiness does not happen. Is there an adjustment to correct this.


I hope adjusting position of the position of the "pivot spring assembly" will help. but you may have to disassemble entire slide assembly to clean it up if it still does not work smoothly. See instructions ... Kirby G5 Bagged Upright Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.


Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you


Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.


Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Purchased the DC28 today. Used it on family room carpet then vacuumed furniture. Took nap. Upon return started to vacuum another area. When the roller is engaged, there is a rattling noise. Removed the bin, did not help. Took off the roller plate looking for debris, did not help. Any ideas?


Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible.You can call us free on 1866MYDYSON - or if you ... Dyson DC28 Animal Bagless Upright Vacuum

My Miele capricorn has started making an odd noise. It seems like something is blocking the engine. I've turned if off and on, and reset it and it still have the odd, almost loud barking noise. The power nozzle also does not seem to be working. I've checked the connections. Right before this happened I was using the vacuum. I didn't notice anything out of the ordinary until this.


Greetings,\015\012\015\012This is a major problem. The Miele vacuums motor should never make a loud noise, period. The way the motor is designed, it's quiet and should be quiet for the life of the motor. There are two motors on your ... Vacuums

Loud noise?? my vacuum suddenly just got really loud. it suctions fine, i changed the belt, but when the roller is off its not loud, but when i put it back on the 11noise is horrific. it vacuums fine i just cannot stand the noise. please help


I have the exact same problem. I've taken the thing apart and cannot figure out what is causing the noise. It's not the belt and it doesn't seem to be coming from the engine. It sounds like the spinning brush is hitting something, but it's not, th ... Bissell 6590 CleanView Bagless Upright Vacuum

I have a multifunction robotic auto vacuum cleaner model number XR210. It doesn't seem to be charging when at the docking station. The light is flashing on the docking station as if it was charging, but then I am getting intermittent noises like the vacuum is about to start up, then it beeps and goes silent again. I have emptied the machine. The display does not read 88 as if there is a malfunction, so I'm really not sure what's wrong with it. If I put the vacuum to the docking station the displ


... Vacuums

Excessive noise Why does my vacuum #877 531 7321 116 36932503 make excessive noise when I use the suction tools on high. There does not appear to be any blockage. It sounds normal when I reduce to medium. The same noise happens when using carpet mode.


... Kenmore Vacuums

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Kenmoor Progressive 360 seems to have a short somewhere between the handle and the head of the vacuum. I believe the short is were the handle meets the wand. Help!


With a multi meter set to ohms, back probe one wire at a time from the motor to the switch while shaking it check for an open. if none are found continue this be on the switch until the open is located. Make repairs as needed. ... Vacuums

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please


... Vacuums

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

A loud noise happens when I try to vacuum carpets. The hose works but that is it. Please help, I just recieved vacuum for mother's Day.


THE BELT MAY BE LOOSE. UNPLUG THE VAC AND USE A PHILIPS SCREW DRIVER TO REMOVE THE UNDERSIDE OF THE VACUUM WHERE THE BELT IT LOCATED. CHECK TO MAKE SURE THAT THE BELT IS ON TRACK AND NOT BROKEN OR SNAPPED. THIS CAN CUSE A LOUD NOISE TO BE PRODUCED FR ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.


... Dyson DC25 All Floors Bagless Upright Vacuum

The electricity in the apt attached to my house lost power in two of the walls. It happened when the cleaning ladies I think were using a vacuum, they don't speak english very well so I'm not sure. I have looked at the circuit breaker a # of times and nothing seems to have been tripped. I have also inspected the outlets and they seem to be fine. Can you help me?


Even know the breaker doesn't look tripped it might be. You have to flip it all the way off and then back on again. That is most likely what has happened. If that doesn't work check to make sure a GFI hasn't tripped. They are usually loc ... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Dyson DC14 Animal Vacuum - terrible loud noise


I have purchased six Dyson DC14 vacuums on eBay at rediculously low prices as they were being sold "as is" because they made a "terrible noise" when the brush bar was engaged. Each of the vacuums I received were like new, literally, and did make the ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have power at top of handle, thus start button light up. but when turn on nothing happens. I checked wiring and it all seems plugged in. The lights on the bottom of the cleaner (part of the base) don't light up. so somehow it makes since issue at base. HELP.. retired cop


Hi,\015\012Seems, the motor of vacuum has no power supply ( not connected yet). You may have a loosen/defective connection on motor cables/terminal. Please check and have it fixed. ... Oreck XL2200 Bagged Upright Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1336 seconds