Having problems with your Hoover Vacuums ?

I replaced the belt with part# 40201 on my Hoover model# U5473-900; to only have it break again in 5 seconds! Is there something missing that holds it on that little bar?


Answers :

Greetings,
\015\012
\015\012When a brand new belt breaks in 5 seconds, this can only mean 1 of 2 things.
\015\012
\015\0121. The roller brush itself may be bad and need replacing. If the roller brush's bearings lock up, and the brush can no longer spin freely, this will cause the belt to burn up immediately after you turn the vacuum on. You may test your roller brush by taking it out of the vacuum, and hold it on the very ends of the brush with your fingertips. Make sure you are only holding the bearing caps and not the brush itself. While holding the two bearing caps with your pointer fingers, try to spin the brush with your thumbs. Does the brush spin freely? If no, then you'll need to buy a new roller bush for your vacuum, unfortunately the bearings are not sold separately on Hoover vacuums. If the brush did spin freely (you should get at least 7 rotations out of one spin) then see reason number 2 below.
\015\012
\015\012Your model uses Hoover Agitator Brush Part 48414132.
\015\012
\015\0122. The belt was installed incorrectly. When a belt breaks immediately like this it can also be a result of it not being installed properly. When installing the next belt, after you have put the roller brush back into place, pull forward on the belt to make sure that the brush spins when you're pulling forward. Sometimes I pinch the belt underneath of the brush roller, and it will not spin freely, and will burn immediately if the belt is pinched.
\015\012
\015\012It really can only be one of these two problems. I hope that this repair solution was helpful to you. If you need me to clarify something, please just request clarification here. If it did help, please be sure to rate my repair Helpful. Thank you so much!
\015\012
\015\012Chris J.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I replaced the belt with part# 40201 on my Hoover model# U5473-900; to only have it break again in 5 seconds! Is there something missing that holds it on that little bar?


Greetings,\015\012\015\012When a brand new belt breaks in 5 seconds, this can only mean 1 of 2 things. \015\012\015\0121. The roller brush itself may be bad and need replacing. If the roller brush's bearings lock up, and t ... Hoover Vacuums

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.


Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

Do you have a diagram of the inside of the brush roller and motor area? I took a machine apart that was given to me and can't figure out how the little belt hooks up to the brush roller, etc. I must be missing parts or something but can't find a diagram to know.


You can find a help video relating to replacing the belt at:http://www.ereplacementparts.com/eureka-426a-stick ... Eureka 426A Upright Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?


Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]


Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Bissell pro heat carpet cleaner, won't move forward. both belts working. is there something that is suppossed to hold the brush bar down so the carpet cleaner uses that as it other set of "wheels"


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Progressive 38613890 The slot on the belt side of frame where the beater bar fits down into a U shaped area that holds it in place has worn and stretched out and does not hold the beater bar in place. Can this be repaired somehow?


... Kenmore Vacuums

Chain tensioner Is it possible to change the chain tensioner of the Husqvarna 240 to a tool less chain tensioner or at least to the chain tensioner where the adjustment screw is accessed from the side not from the front. The problem is that there is a little plastic part that breaks rendering the chain tensioner useless. I have changed it twice and it keeps breaking. To change it you have to change the whole part that covers the break and chain mechanism.


... Husqvarna DMS 240 Core Rig - DMS 240 w/ Vacuum Pump

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

My dyson dc31 will not hold a charge and only runs for about two seconds then you have to release the trigger then it runs for another 2 seconds and so on.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out


Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a canister with a beater bar which i love. I have sucked up a sock (or something) in the beater bar and it will not work. I can't get it open to check it out. We have misplaced the booklet that came with it.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=820565\015\012Generic problem for all Vacuums\015\012I have a canister with\015\012Posted by DFundis on ... Vacuums

I need to remove the motor in my ricar 4812 (to change the axle) Where can i find something on that? I have 4 screws out- but it seems to be held into the body where the shaft goes out to the belt. Just missing something dumb.


... Riccar 4812 Vacuum

Dc07 model, cannot get it to stand fully vertical upright. It is as if something is not sliding back into position right. Don't want to force it in case something breaks. The upright of the cleaner has been dropped from time to time. Any thoughts on sorting it out?. Thanks a lot. M


Hi, Try this quick repair and see if this fixes your Dyson in terms of not going in the upright position: This is a frequent problem that we see come in on Dysons. If this doesn't fix it, please feel free to just use the clarification req ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Eureka Pet Pal and I think I have something caught in the bar and is not rotating. How do I get to the bar to check?


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

We have already spent $60 on getting the belt repaired once. This time, the same thing is happening, the belt is jumping of the small metal bar in the back of the housing. Seems like there should be something on the end of the bar to keep the belt on it?


Greetings from GoVacuum,\015\012\015\012Ahh, the Hoover Windtunnel Self-Propelled model. This model has a some reoccurring problems with it. The majority of them have to do with the b ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

My Dyson has very little suction.....just a little on the left side. The cylindar is not full...could something be stuck?


The filter and filter housing could be the issue, check this article out:\015\012\015\012http://www.ehow.com/how_5870417_modify- ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0548 seconds