Having problems with your Hoover Vacuums ?

We have a Hoover Tempo, and the brush stopped moving around. How do you get the brush to move again?

Answers :

The most probable problem is the belt that runs the brush broke. Purchase a new belt for that model and replace.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Hoover Tempo, and the brush stopped moving around. How do you get the brush to move again?

The most probable problem is the belt that runs the brush broke. Purchase a new belt for that model and replace. ... Hoover Vacuums

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.

Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

My hoover spin scrub machine has stopped scrubbing. It still dispenses and pulls up the water, but the brushes don't move. I've checked the on off button for brush control and cycled it to off and back on, but no movement out of the brushes.

There is a filter on the front right hand side of my F5871-900 Hoover. If you remove the plastic covering and clean that filter (wet finger may do), you're Hoover will begin spinning again! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old

If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]

Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.

... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

I have a hoover carpet cleaner model # F7427-900 series Z120 and the rotating brushes stopped moving. How do I fix this?

The brushe until needs to be snapped in very hard; to line up correctly. Pull the unti off and put it back in, good luck. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The brushes on my Hoover Steam Vac F5919-900 stopped spinning. How can we get the panel off to check belts etc.?

... Vacuums

Hoover spinscrub brushes have stopped spinning and I can not get the filter out of the bottom

... Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!

... Hoover Vacuums

Hoover steam vac F7427-900, brushes stopped

This is not correct, the turbine bearings are NOT sold separately. Hoover only sells the entire turbine gear assembly complete, not in separate parts. \015\012\015\012To verify this, please see the parts diagram below, you'll see that ... Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up

Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!

... Roomba Robotic Floor Bagless Vacuum

Roomba 4270 stops too soon. my roomba got weird all of a sudden. it started not moving all over as it should. so I tore it all down as I had done before and cleaned all the hair and dirt out of every thing I could without getting down to the basic shell. it does work now and does move all over but stops after about 10 minutes. brand new battery so not a battery issue. could I have plugged some of the sensors in the wrong 'plug'

... iRobot Roomba 560 Robotic Vacuum

My Hoover sprint 1700w has stopped working. I thimnk it could be the fuse. How do i get the plug apart to get the fuse out? Can you give me other possible reasons it could have stopped working?

... Vacuums

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.

Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???

... Vacuums

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech

... Vacuums

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move

There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1181 seconds