Having problems with your Hoover Vacuums ?

Our Hoover U8172-900 brush motor is not working. Do you have a wiring diagram so I can determine if the motor circuit board is the problem or the motor?


Answers :

No diagrram is necessary unless you have dismandled.
\012Check if the brushes are touching the mtor commutator. If not you can easily remove both the brushes and polish the surface evenly .Insert only after cleaning the motor commutator till the copper shines.
\012Use can check for the continuity of the brushes to show that the armature is working Ok.
\012Now check the filed winding. Both the windiings must snot show any leak or short to the body. If so the motor is fault.
\012If field is ok with the resistance check then check for power supply to mtor when switch is triggered . If not check cord and switch.
\012Hope this tip helps.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Hoover U8172-900 brush motor is not working. Do you have a wiring diagram so I can determine if the motor circuit board is the problem or the motor?


No diagrram is necessary unless you have dismandled.\012Check if the brushes are touching the mtor commutator. If not you can easily remove both the brushes and polish the surface evenly .Insert only after cleaning the motor commutator till the ... Hoover Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering


Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board


The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Check the cord to make sure you have continunity throw both leads, check them at the cord reel, there are 2 wires hooked up to it, if not then the cord is bad. Check the swith also, the next cause would be the speen control mounted on the motor, par ... Miele Cat & Dog 326i Bagged Canister Vacuum

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Hello, First check the cord to make sure you have continunity throw both leads, check\015\012them at the cord reel, there are 2 wires hooked up to it, if not then\015\012the cord is bad. Check the swith also, the next cause would be the\015\0 ... Miele Cat & Dog 326i Bagged Canister Vacuum

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.


If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

Makita 440 Dust Extractor - Trying to rectify a problem, when i switch on an appliance plugged into the socket, it will not run. IS used to run with this plugged in, but the hoover motor runs no problem. Any ideas what might be amiss, or where i can get a wiring diagram? Thanks in Advance!


... Makita 440 Wet/Dry Vacuum

Rewiring kenmore vac with circuit board need wiring diagram for mdl 116.22271501c


... Kenmore 23313 Whispertone Bagged Canister Vacuum

I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line


Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My Bissell Proheat 2X brushes are not turning. I have narrowed the problem down to either the brush motor or the circuit breaker How do I determine which unit is at fault?


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram


... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

I Have a kenmore 116.23612300 canister vacuum which will not start. I have power everywhere but nothing going to the black wire to the motor. Seems to stop at the pcb asm, #KC86WBZRZ000 . Nothing from there to the black motor wire. White wire to motor has continuity everywhere it should. Ruled out just about everything but the PC board. What does it do exactly?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Meile vacuum S4210 seems to have a circuit board problem


... Miele S 4210 Bagged Canister Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Wiring diagram Need wiring diagram for the motor wiring.


\015\012\015\012HI, tell me is this you want,, \015\012\015\012Gunjan:-) ... Vacuums

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a


Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Need wiring diagram for riccar supralite vacuum, replacing motor, old motor has two wires, new motor has three


... Riccar Liteweight & RSL1A RSL3 RSL4 RSL3C vacuum bags 6pk

Wiring diagram for Dyson DC05 Motor. Bought a replacement motor and wiring slightly different from original. Thermal cutout on both motors.


... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0491 seconds