Having problems with your Hoover Vacuums ?

Motor is running and the brush is also running but i have no suction and the suction tube is clear


Answers :

A clogged filter or if it has a bag hole in bag or bag isn't in correct.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor is running and the brush is also running but i have no suction and the suction tube is clear


A clogged filter or if it has a bag hole in bag or bag isn't in correct. ... Hoover Vacuums

My dyson vacuum motor is sounding very high pitched... The tubes are all clear and there is suction with the tubes not not real good suction on the beater brush area....


If you have tried cleaning other parts and cannot find an obstruction, and still have no suction, you could try this:\015\012\015\012 ... Vacuums

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.


Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.


If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

My dyson slim dc18 has suction in hose attachment but no suction in floor attachment. Tried to clear any obstruction by running clothes hanger in rectangular opening that empties into cannister and also tried to blow air through there also but still can not get suction


Hi its Darran at Dyson.It would be worth checking that the brush bar is turning when the machine is in the vacuuming position. If it is not turning, please press the re-set switch located on the cleanerhead. If this starts th ... Sharper Image Dyson Slim DC18 All Floors Vacuum

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?


Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?


Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?


As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and


The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson DC07 has no suction. motor runs, brush spins, just no suction.


Hi..the reason to this problem may be the bottom pieces \015\012might not have been fully seated.Take it apart and put it \015\012carefully back together.This will solve the issue.\015\012check it out..\015\012thank u..\ ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?


There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

<2 year old Eureka 4870DT with strange noise and aweful smell from motor. Roller also not rotating. The belt is intact and all tubes are clear. Do I need to replace the motor?


The price of vacuums these days are falling all the time - esp on EBay. This sounds like there's a foreign object or simply dust which has managed to get into the motor thus causing the burning smell or that the roller brush fly wheel is loose and ca ... Vacuums

Hi. DC14 not running. Repeated pressing of the switch occasionally produces a split second whirr from the motor. I had been picking up plaster dust for some time but stopping regularly to clear out filters and 'the little tubes.' The switch is fine. I cannot see how to get at the motor. Thanks , Chris


Hi again. I finally figured out access to the motor. One of the brushes was burnt and broken. I have ordered a replacement set and cleaned up the comutator ( spelling ?). Thanks, Chris ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I have lost suction on my Bissell. It is also clogging in the Plastic tube that runs from the roller to the hose. What could have caused this? All filters have been cleaned, tube as well, but the problem still persists.


... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

NO SUCTION ,EITHER AT WHERE THE HOSE GOES IN OR AT THE MAIN NOZZLE. WHAT COULD BE THE PROBLEM, HOOVER ELITE? ALSO MOTOR IS RUNNING AT A HIGH SPEED THAN NORMAL.


It might be clogged. ... Hoover Elite U5349-900 Upright Vacuum

Motor runs,brushes turn,no suction - Vacuums


Either the fan on motor is broken or off shaft or the unit is plugged,if its plugged the motor will sound like its running faster than usual ... Vacuums

When we plug in the hose the motor in garage runs but no air or suction comes out of the outlets. we cleared all the lines too.


Check to see if you have suction at the unit. If you have suction at the unit, your pipes are stopped up. If you don't have suction, you have a pipe loose under the house. Also you could just have a stopped up hose ... Electrolux Centralux Vacuum

Aquavac runs for short time then cuts out blowing the RCD . Have rewired mains cable thinking a broken or loose wire... still same problem. Have also noticed that a lot of sparks etc coming from the motor brushes. Vac approx 10-15yrs old.Aquavac is model 6310B


... Vacuums

Motor runs brushes but no suction - Vacuums


Blockage? ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1077 seconds