Having problems with your Hoover Vacuums ?

Need to replace the handle-release lever on a Hoover model U8125-960 Vacuum cleaner


Answers :

The exploded views at this URL will help you identify the part and you will be able to order it as well.\015\012
\015\012http://www.ereplacementparts.com/hoover-u8125960-savy-bagged-and-bagless-vacuum-parts-c-37315_37337_37538.html
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to replace the handle-release lever on a Hoover model U8125-960 Vacuum cleaner


The exploded views at this URL will help you identify the part and you will be able to order it as well.\015\012\015\012http://www.ereplacementparts.com/hoover-u8125960-savy-bagged-and-bagless-vacuum-parts-c-37315_37337_37538.html ... Hoover Vacuums

The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?


You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

How do I insall a handle release lever on a Bissel upright model 3522 vacuum cleaner


... Bissell 3522 PowerForce Bagged Upright Vacuum

Remove & replace handle release lever on hoover model U6445, s/n 039900015686


From under the vacuum, there is a tab release that you need to pry out the old part. At this point, based on your serial nuimber, your vac is over 10 years old and may also need the base. The bracket is part of the base and not expensive, but the rep ... Vacuums

How to replace the handle release lever - Hoover U6446-900 WindTunnel Bagged Upright Vacuum


... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Replace handle release lever part 38458042 - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

Hoover Mod U8146-900-When you press handle release lever vacuum falls down it doesnt stay up


... Hoover Vacuums

How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

I have a Hoover steam vacuum carpet cleaner Model


The lever on the handle should be pressed when you want to apply solution to the carpet ... Vacuums

How do I replace the handle release lever spring on a Eureka Pet Pal vacuum?


... Vacuums

How to detach handle from the Hoover vacuum cleaner model U6425-900?


Click here > http://hoover.com/file/496/ for the manual for full instructions.. ... Vacuums

DM4470 001 Hoover Vacuum Cleaner. How do I remove the "Handle Release Pedal"


... Hoover Vacuums

How do you replace the handle release lever on the hoover windtunnel 6425-900


The release lever is held in place by tabs molded into the base. You just need use a screwdriver or two to press the plastic tabs back and then push the release lever out. The new release lever can be just pushed into place and the plastic tab ... Vacuums

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

How to replace vacuum handle pedal release on hoover dm 5530


... Hoover Vacuums

Want to remove and replace detent lever or handle release pedal part # 2031044 on Bissell powerforce model # 3525. How is it done?


... Bissell Vacuums

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.


It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I need to replace the belt on the power nozzle of my Hoover Dimension 1000 Model S3491. Unfortunately, I have no written instructions on how to do so. I purchased the vacuum cleaner in the mid-80s. Are the instructions still available? Thanks in advance.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566792\015\012Generic problem for all Vacuums\015\012I need to replace the\015\012posted by Deb in Iowa ... Vacuums

After replacing the flat bet and v belt on my Hoover model U6433-900; serial No. 12300043057, purchased June 23, 2004, the brush roller still does not turn when I release the foot lever to vaccuum.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=725351\015\012Generic problem for all Vacuums\015\012After replacing the flat bet\015\012Posted by maha ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1885 seconds