Having problems with your Hoover Vacuums ?

How do you install the torsion spring onto the front wheel unit of a Hoover vacuum, model U5760-910? Thanks!


Answers :

Is this what you're looking for? snakysmom.jpg

Also,the manual for your vacuum is available online at http://www.hoover.com/CustomerService/Manuals/Default.aspx.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you install the torsion spring onto the front wheel unit of a Hoover vacuum, model U5760-910? Thanks!


Is this what you're looking for? Also,the manual for your vacuum is available online at http://www.hoover.com/CustomerService/Manuals/Default.a ... Hoover Vacuums

How to install the torsion spring - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to install cam actuator spring on hoover upright vacuum model u5253-900


... Hoover Vacuums

Hoover vacuum (Legacy 740) with broken wheel axle assembly unit


... Vacuums

I am replacing the front wheel assembly and TORSION SPRING on a windtunnel bagless model U5750 and I can't figure out where the torsion Spring is supposed to go?


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Installation of front wheel assembley on a hoover vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How to replace the torsion spring on Hoover WindTunnel model U6630-900


... Vacuums

ASSEMBLY HOOVER U5432 WHEEL AND SPRING BACK ONTO VACUUM


... Hoover U5432-900 WindTunnel Plus Bagged Upright Vacuum

Hoover model#u5215-930 wheel assembly - Hoover Vacuums


... Hoover Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Hoover windtunnel wheel spring location - Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum


Hello irishud. Go to searspartsdirect.com\015\012\015\012Enter your model number and you will get the schematics that show you exactly the wheel spring location. Joe\015\012\015\012Thanks for choosing Fixya! ... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum

Install hoover vacuum wheel assembly


... Hoover Vacuums

How to install a detent spring on Hoover vacuum


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity


... Vacuums

I have a Hoover U5750 Windtunnel vac. I had to replace the front wheel assembly and don't remember where/how the torsion spring goes.


... Hoover Vacuums

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

How do you fit a hoover wheel spring carrier - Vacuums


... Vacuums

Torsion spring lock on miele hoover s5211 - Miele S4210 Antares Bagged Canister Vacuum


... Miele S4210 Antares Bagged Canister Vacuum

How to install front wheels on upright hoover vacuum cleaner


Please be sure to unplug the vacuum before doing this. Pull the sides from top cover on the floor portion (Where the light is) and it pops right off. After the cover is off, step on the lever to tilt the handle back like you are going to sweep. Lay t ... Hoover Vacuums

Install torsion valve arm spring on UH60010 hoover vacumm


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to replace the torsion spring on my Hoover WindTunnel model U6630-900


... Hoover Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover vacuum windtunnel model U6630-900


... Vacuums

Need a front wheel assembly for my Hoover Tempo model u5144-900. I see similar looking Hoover wheel assemblies online for different models, will they fit mine?


The Tempo series cleaners look similar, but are different colors. The wheel assemblies will work if they look identical in appearance to yours. ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

My Hoover vacuum model - U6317-930 lost power. I


Something is definitely loose in that area. Replacing the related parts is probably the best fix. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1186 seconds