Having problems with your Hoover Vacuums ?

How to replace the belt on a hoover vac model u4295-930?


Answers :

Take off the bottom plate, the belt goes from the brush roll to the motor shaft. If you can't see the motor shaft, then take off the top cover. There may be a couple of screws to remove from the bottom, then there is a ctach on each side from the bottom use a flat blat and pry out to release them.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace the belt on a hoover vac model u4295-930?


Take off the bottom plate, the belt goes from the brush roll to the motor shaft. If you can't see the motor shaft, then take off the top cover. There may be a couple of screws to remove from the bottom, then there is a ctach on each side from the b ... Hoover Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

The belt is broken on our Hoover Allergen Filtration Model U5018-900 120 v. 60 Hz 12.0 A. Belt 38528040. Where can I get the belt and instructions on how to replace the broken belt?


The owner's manual can be downloaded here (in red, "Download the Instruction Manual (PDF))\015\012http://www.hoover.com/product.aspx?model=U501 ... Hoover U5018-900 Bagged Upright Vacuum

I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?


Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum

Need instructions on how to replace the belt on a hoover dirt finder model u5321-930


You can download the manual from the link below:\015\012\015\012http://www.hoover.com/Media/ModelPDF/U5468900.pdf\015\012\015\012Please update the question & let us know if the information given was useful to you - Good Luck! ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Belt replacement Does Hoover Windtunnel V2 model # U8148-900 even take a belt? The owner's manual only describes how to change belt in powered hand tool, not the vacuum itself.


No belt- it is motor driven. what happens to these if the rollers get stuck(by- say, a Lego® or something)  is the roller itself has an insert which will break, requiring roller replacement. \015\012\015\012simple fix, but costs a ... Hoover WindTunnel V2 U8148-900 Upright Vacuum

I need to replace the belt on my hoover fusion plus upright vac. But I cannot find what belt it takes. the number on the belt is worn off


Hello : \015\012\015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Replace belt on Hoover Model #U6430-900 - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I need a replacement belt for Hoover Elite upright vaccum ,model no. U5043-930. What belt do I get?


Hello, \015\012\015\012Your vacuum cleaner originally came with Hoover belt part number 38528027, however Hoover has now discontinued this part number, and replaced this belt with the new belt which is part number 38528040.\015\012 ... Hoover U5227-930 Elite Upright Vacuum

Belt repalcement how to replace the belt on Hoover model no. U8130-900


Hello,Here is a link that will explain with illustrations how to change belt. You will see 2 links. Click them and use the link that is closest to your machine. ... Hoover U8130 V2 Vacuum

Problem with small belt and beater bar spinning. Where to get replacement belt and what is it called model number. Thanks. Only 2 months old 5780-900 Hoover windtunnel cyclonic


Here you can get a package of the belts you need. Also here is a link to the manual:U5780-900 Belts\015\012\015\012\01 ... Vacuums

Changing belts I cant figure out how to replace belt on my hoover cleaner model u4537-910


Turn vac over, remove the 4 screws holding the bottom plate covering the brush roll. There are 2 belts, one is a V belt ( 38528034) for the brush roll, the other is a flat belt (38528035) that goes from the larger pulley and the motor shat, put it o ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacement belt # for hoover wind tunnel model u5750-900. original belt # 38528-035, please


Your belt number is correct ending in 035. I have had luck with belt number ending in 033 also. ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

How do I replace a belt on a Royal M1030 commercial Vac? What is the belt model number I need to order---thank you


Go..\015\012http://www.youtube.com/user/GoVacuums?v=meX8lgZo7DY&feature=pyv&ad=3168329782&kw=how%20to%20replace%20a%20vacuum%20belt&gclid=CL_478KwgZ8CFRAeDQod7mI1NQ ... Royal 5300 Upright Vacuum

How do you replace the v-belt o a hoover Model U6432-900


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do i replace belt tensioner on hoover model # u5753-960


... Hoover Vacuums

Replace the belt on Hoover upright model # U4655-930


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0861 seconds