Having problems with your Hoover Vacuums ?

Hoover 6634900 self propel will not work. - Hoover Vacuums

Answers :

The hoover series sometimes has a belt driven gear or a plastic gear assembly that gets worn out. You may have to replace one or the other to see if this does the trick. Becareful not to loose the little screws that holds the assembly in place. Some models has a clip that holds it all together, some do not have any of them at all.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.

Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover 6634900 self propel will not work. - Hoover Vacuums

The hoover series sometimes has a belt driven gear or a plastic gear assembly that gets worn out. You may have to replace one or the other to see if this does the trick. Becareful not to loose the little screws that holds the assembly in place. Some ... Hoover Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover self propelled vacuum not working

... Hoover Vacuums

My hoover wind tunnel self propelled vacuum wont stand up be itself. The locking thing is not working. Thank You. [email protected]

If you look at the foot pedal, see if it is locked in the base, and pivots freely. I have seen some of these that break the base, or break the spring hinge on the back side of the release pedal. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Self propel doesn't work - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The flat belt under the bottom is the most likely cause. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover self propelled WindTunnel vacuum( Model U6425-920) that stops in the middle of cleaning. I have changed the flat belt and I'm still experiencing the problem. I usually have to wait an hour or so b/4 it would work again. Any advise?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=632298\015\012Generic problem for all Vacuums\015\012I have a Hoover self\015\012Posted by thjunk2007 o ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Hoover Windtunel Self-Propelled Upright Vacuum, Power Drive Not Working

Have you checked the belthttp://www.youtube.com/watch?NR=1&v=wRoqZnZ4h0w&feature=endscreen ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou

... Vacuums

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel

Here is a video how to fix ... Vacuums

I have hoover WindTunnel Self Propelled Vacuum

Greetings from GoVacuum,Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Bagless Windtunnel - Self Propel feature not working

I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Self-propel not working on my Hoover Windtunnel

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?

This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.

... Vacuums

Hoover self-propelled self-propel not working. belts ok.

No suction on Windtunnel 6630-900. All belts work, brush turns, it just won't pick up anything. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Self-propelled Broken? Vacuum very hard to push. Self -propelled doesn't seem too be working. What can I do?

I have the same problem, found out there is a cable that is broken, I'm trying to figure out how to fix it. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Self Propel The vacuum will not work in a self propelled mode.

Me again with more info. This happened to me and I solved it as described previously. More info here:There's a microswitch located where the hose attaches to the bottom section of the vacuum. If the hose is not completely inserted, th ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900

May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum

... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover self-propelled u6630-900 reverse not working

THe forward/reverse lever (made of plastic) possibly is broken. New part is about $10.00 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Installing belt on hoover self propelled upright vacuum

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40544&thid=641399\015\012Installing belt on Hoover self propelled upright...\015\012Posted by Fryeburger on Jun 02, 2008 ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0984 seconds