Having problems with your Hoover Vacuums ?

Hoover Bagless Windtunnel (tank tyle) selfpropeled head throws belt; 2nd one doing exactly as the first vacumm.very hard to put it back on .can't even get one room done

Answers :

Is this a new belt? If not, get a new one. Check the brush roll, make sure the ends are turning freely, if not, replace it. If you are catching things like a throw rug and towell or some other thing, this will cause the belt to get knocked off of the motor shaft.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Bagless Windtunnel (tank tyle) selfpropeled head throws belt; 2nd one doing exactly as the first vacumm.very hard to put it back on .can't even get one room done

Is this a new belt? If not, get a new one. Check the brush roll, make sure the ends are turning freely, if not, replace it. If you are catching things like a throw rug and towell or some other thing, this will cause the belt to get knocked off of ... Hoover Vacuums

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition

Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

I bought a fantom vacuum on HSN about 9 years ago.Whan it was delivered the first one was broken so they sent a second one.tThat one also was cracked on covering for brush. I called and they told me they were no longer available,so I kept that one,since it would cost me shipping to return.The back right side wheel evenually cracked and fell off.I was able to put it back on and it would stay for a few weeks or so.It now has a large piece of plastic that has broken off the wheel where the bolt fit

... Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor

On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bought a shop vac about 3-4 mos ago and while i was using it, it cut off and wont cut back on. This is the second shop vac that done this and I took the first one back and got this one and it did the same thing. It is a 12 gal. 4.5 peak hp.

... Shop Vac 401-12-00 Wet/Dry Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet

Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have bagless samsung air track 2000w tein cleaner vaccume cleaner..it has only one switch for on and off...cant find a switch to put the cord back????? .

... Vacuums

I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th

Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

I recently put a call into dyson regarding a problem with my vaccuum and a supervisor was supposed to get back to me. no one has. back in august, we were on the phone with a technician regarding a problem with out machine. after trying a list of things, she said to take it to american vaccuum services and it would be covered by dyson. when i did, the man told me it was clogged and i would owe $45. i would not have taken it for that price! please advise as now i am stuck. i want my vaccuum and th

Unless you can Dyson to intervene and have this repair covered under their warranty, You are stuck to pay for the service. Clogs may not be covered under warranty, but I don't know how their warranty states. If it says that if you have a problem, t ... Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?

If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?

There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My kirby is shorting out when i plug it in and turn it on it wont turn on and then after a little bit it will turnon but twhen you move it it will turn back off.. and there were sparks from the cord.... i was wondering if i still have a warrant to get another one ive never had a problem with my kirby i love it but am dissapointed that i cant use it

... Kirby G5 Bagged Upright Vacuum

I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I'm wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.

I'm no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction. ... Eureka Smartvac 4870 Bagged Upright Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????

Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tried to take roller brush out to clean it's housing, cant get one side back in without trying to force it.

The roller brush fits snug in the housing, however, if you had it out, check to make sure the end caps of the brush shaft are pushed all the way on. These just slide on the roller bar shaft and if something got under them, they would not be able to ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.

First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I

Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0886 seconds