Having problems with your Hoover Vacuums ?

Hoover S3670050 how do I open the unit up, to replace a cicuit board?

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover S3670050 how do I open the unit up, to replace a cicuit board?

... Hoover Vacuums

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray

This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I

Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Replaceing the circut board henry hoover

... Hoover Vacuums

Hoover Savvy U8174-900, replacement circuit board LED/Brush Motor

\015\012 \015\012 \015\012 \015\012 \015\012 ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Replacing propeller Kirby G5: ordered a new propeller and can't seem to open up the unit to replace it. We've found all of the screws (we believe). Are we missing something?

This will help you out tremendously...\015\012\015\012http://reviews.ebay.com/KIRBY-VACUUM-RE ... Kirby G5 Bagged Upright Vacuum

How do I replace the Powercord on a Fantom XT64K Vacuum. The powercord shorted where is comes out of teh housing. I need to open up the unit & replace but need a service manual of instructions. Thanks Father Lenny

I have done this several times, it's some what simple just take the unit apart and use the old diogram to replace the new one. Or take a digital photo of it opened so you have your own scematic. You should be able to purchess the cord at your local h ... Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Where does it go and how do I replace the belt on a Deluxe Hoover Mach 3.8 bagged windtunnel action vacuum? I kno it goes somewhere around the brush but it fell off when opened and I can't tell where it goes. I have a replacement belt

... Hoover Vacuums

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?

... Hoover Company Wind Tunnel U53019 Upright Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

I have a Hayden SuperVac 3600, almost 10 years old. The unit still runs, but now when I switch to the power nozzle, it doesn't have power to turn that. I think this happened once before and maybe they replaced a circuit board(?). We took it to a local repairman this time and he says he can fix it temporarily with a new cartridge, but that he won't promise it won't happen again soon.....

The hose has fuseable link inside, generally a 3-7 amp. It is at the wall end underneath the hose cuff. Easy to replace as it crimps in line. If you have a meter you can also test the detachable hose to wall cord for continuity, then check the hose t ... Hayden Industries SuperVac 6000 Central System Vacuum

To : admiralstopf I have a U-Line clear ice maker UCLR2060B40. The authorixed service center has been trying to fix my unit since October to March. They have replaced the circuit board 2x and the Thermister and rain tube. They clai they were able to get it to work on their bench (not sure if true) but they can not get it to work in the house. They gave up and refunded my payment. Now what? Jonathan

Unfortunately we are not affiliated with any manufacturers. What I would do at this point is to contact the manufacturer of your ice maker and let them know what has transpired when you attempted to have their authorized repair center fix your issue. ... Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current

I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)

... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

The electronics in my Sunbeam TA200A Toaster is playing up. The Toaster is sometime popping the toast up after the right amount of time, but sometimes it pops up a minute later than it should (burning the toast) I have open up the control panel buttons and inspected the array of transistors and resistors that is used for the timing mechanism and a visual inspection doesn't indicate a problem. I am keen to replace the 2 transistors on the control unit (the resistors are unlikely to fail) but I ne

... Vacuums

I have a Hoover Telios T5732 with broken cable winder, have purchased a replacement winder unit have loosened 5 screw but still cannot separat the covers . some advice please.

After unscrewing all the screws, try to open it evenly, not more from one side.\015\012check this link, \015\012 ... Hoover Vacuums

How do I open up my hoover to replace the belt. my model number is U5068-900

Hello,Here is a link to a guide with illustrations to guide you. http://www.fixya.com/support/p41322-hoover_u5 ... Hoover U5068-900 Sprint Upright Vacuum

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940

You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

I have a Hoover upright Model # U5445-900. I am trying to replace the power cord but can not find access to the inside of the unit. thanks , Paul

Paul\015\012\015\012Should be screws holding the handle together. They put it in, it had to go somehow. Look for holes that maybe covered over.\015\012\015\012Paul, these are general tips, I am not familiar with this specifi ... Vacuums

How do i open my hoover u5131900 to replace the belt

On the bottom, turn screw-like objects and it will pull apart ... Vacuums

Our roomba 560 wont charge have replaced the battery Tested the charing unit with another roomba that all seems ok put the uncharged battery into another Roomba but im guessing it now has a memory as this wont charge in the other hoover. Any ideas what may be wrong

Try cleaning the battery contacts with a little rubbing alcohol or contact cleaner on a foam swab, or a bit of paper towel. Take a litle time, it doesn't always dissolve instantly. (Don't use a pink pencil eraser, it would scrub off the plating that ... iRobot Roomba 560 Robotic Vacuum

Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?

... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0811 seconds