Having problems with your Hoover Vacuums ?

My Hoover Steam Vac model f5915-900 no longer heats the floor to reduce drying time. I have cleaned the bottom of the machine where it says "heated cleaning." Anything else I can try? Thanks.

Answers :

The SteamVac blows warm air from the motor into the carpet to help loosen oily types of soil. If the motor is running, the air will be exhausted. This system is not meant to reduce drying time, but only to enhance cleaning.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Hoover Steam Vac model f5915-900 no longer heats the floor to reduce drying time. I have cleaned the bottom of the machine where it says "heated cleaning." Anything else I can try? Thanks.

The SteamVac blows warm air from the motor into the carpet to help loosen oily types of soil. If the motor is running, the air will be exhausted. This system is not meant to reduce drying time, but only to enhance cleaning. ... Hoover Vacuums

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine

... Bissell 8910 ProHeat Clear View Upright Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


My bissell pro heat clear view is not spraying when I press the trigger. what is the problem? I have check the belt and clean the machine. Is there something else?

I believe the water pump is broken. You can order a new one for about $22 and try to install it (it is located under the plastic near the cleaning solution holder). It requires removing quite a few screws, but if its just the pump, its easier than ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I purchased a brand new Techno 1000 Fog Machine last Halloween. It worked fine, but once I ran the cleaning fluid through the fog machine only heated up and produced no fog. A year later and now won't even heat up at all, even after replacing the fuse!

... Vacuums

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

Cleaning! To clean the cyclonic cone Dyson say to use can-air? that may be ok for computers but not to blow out the dirt and dust from the cone in question. Someone else here suggested to use a real compressor! Well dahhh I knew that! Should I do the blowing in the living room? or may be in the bathroom? Seriously what I need is an assy. drawing to take it apart and washing it Any ideas where I can get one? Thank you John

Hi, we realy love our Dyson, but get frustrated when it gets clogged with pet fur (2 cats and 2 dogs). This takes a little effort but what we ended up doing was taking the vacuum apart into its major components and alternately blowing it out, filter ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka Atlantis Opti Heat model no.2596. The bottom is cracked and the clean water and shampoo leaks all out the bottom. Is there a repair part for it. I've only used it 4 or 5 times and i really need a new part.

... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

I cannot get the sprays from either the bottom or the handpieces to work. I only get a short "gurgle" of fluid when I first press the controls. I have cleaned both the top and bottom cap and insert parts, and I have turned the machine off and on numerous times, have allowed it several minutes to warm up. But still no luck. Bissell Turbo 2X 9500 series (3 years old) D B Davis Camas,WA

It sounds like the pump has malfunctioned. I own a Bissell Big Green Clean Machine.You can actually order a 50 foot hose and run it from the sink to the hand piece or the part that is supposed to spray to the floor. This hose can handle ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell pro heat- I put the soap dispenser in and it all comes out the bottom of machine in about 2 min. The machine isn't on. It just drains through to the floor. Whats wrong?

... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

SEBO vacuum cleaner makes a strange noise and shuts itself off after a few minutes. Suction not working when tube is attached, but works with hand-held portion only. Indicator light saying bag is full/clogged is on, but we've cleaned out the bag, cut away any fur/strings that were wrapped on the turning portion, and cleaned out the refuse valve. Not sure what else to do. Thanks!

... Sebo Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell proheat 2x carpet cleaner is not spraying from the bottom or sucking up when turned on. The hand tool works just fine. I have made sure it was on floor cleaning when I used it to try and clean my carpet. the busshes are working but nothing else is happening this cleaner is about 21/2 years old and has only been used maybe 5 times so it has not had alot of use.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The clean water is leaking straight out through the bottom of the machine. This just started out of the blue. I cannot use the machine because of this. Any ideas?

It sounds as if the reservoir is stuck open. If you look behind the upper tank, you will see a rod that opens the reservoir when the handle release is squeezed. This part may need replacement. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Cannot get the crown nut off the bottom of machine to clean the separater

It is imperative that the separator fan clean is kept clean. I recommend that you remove the separator fan and clean it every time you empty out the water basin. The nut that hold the separator fan onto th ... Rainbow E series Canister Wet/Dry Vacuum

I am having trouble with the nozzle control knob on my Hoover Elite Upright. I was cleaning out the bottom of the machine and the knob fell out and now I cant align it properly. It seems loose and not doing anything when I move it

Hello : My advice to take it to the service if you still have the guarantee . Or provide detailed information about your Hoover to get better help . good luck . ... Vacuums

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself

Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.

The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

It says it is a Bissell 12 Amps Pro Heat with Safeguard, and a light indicator on it. So basically it is not spraying out water. I just got it serviced today and cleaned.

Take it back to the place where you had it service/cleaned and tell them to do it RIGHT! ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My problem is the leak is right where clean water tank sits, its on the bottom where it attaches to machine!!! i went through the booklet for instruction , i found nothing! what could it be?

Dirty, damaged, or missing gasket under tank mounting point. Possible damage at tank under-surface. ... Hoover F5906-900 Upright Steam Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.

Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.

You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

I want to clean fluff from underneath the transparent front panel of my Bissell 11 7901. I have removed the screws from the bottom of the panel, but it remains firmly in place. I do not want to apply apply forceful leverage in case there is something else that needs to be done before the panel will come off. Any suggestions, please? Peter

I just did this one myself, You've done most of the hard work already.Be sure your holding tank is out and not in the way.Double check the down front screws are still out since you sent in you question. Now tweak the front section (the business end) ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?

Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0980 seconds