Having problems with your Hoover Vacuums ?

My hoover windtunnel u6323-930 has dust leaking into air when unit is on. i think it is in the housing I cannot see and I need ti know how to take apart to determine which part i need to order thanks David Macali


Answers :

You will just have to start taking the base aprt until you can get the motor, Just remember how it was so you can put it back together correctly again. When you have the motor off, look at the fan chamber, you probably have a crack or hole in it. You can replace the part if it is bad #38736019.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover windtunnel u6323-930 has dust leaking into air when unit is on. i think it is in the housing I cannot see and I need ti know how to take apart to determine which part i need to order thanks David Macali


You will just have to start taking the base aprt until you can get the motor, Just remember how it was so you can put it back together correctly again. When you have the motor off, look at the fan chamber, you probably have a crack or hole in it. ... Hoover Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Parts diagram I have taken the assembly apart and I would like to see a diagram in order to know the part numbers that i need to order for repair.


You may like to try here see if yours is listed http://onlinevacuumparts.com/s-3-bissell-vacuum-parts.aspxriz. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How to I take apart my miele in order to see if the belt needs to be replaced It's a 183 dark blue model


... Miele S185 Powerhouse Bagged Upright Vacuum

Need to know how to take it apart


You should be able to grab it and pull it out. It just sits in the hole, if you have to use something sharp that you can push into it enough to pull it out. You also didn't give me your email addy to email you the picture. ... Hoover F7220900 SteamVac V2 Upright Vacuum

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

I need to know how (if) I can take apart a Miele electric telescoping wand apart to clear some debris from it. Thanks!


Take a close hanger, Or a stick end push it though to clean it out. ... Vacuums

I need to know how to put together a Hoover Slider vaccum. I had to take it apart and now i need to put it back together.


... Hoover S2105 Slider Bagless Stick Vacuum

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I'm not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No foam/water is coming out of my Kirby shampooer. I think it may be clogged, but don't know how to take it apart to see.


... Kirby G5 Bagged Upright Vacuum

DC28 Clutch DC 28 Clutch made knocking noise after about 1 hr of use. Tried to take it apart and see it it had an obstruction but burned up the belt and damaged clutch. Yes, I know I should heave taken to the dealer or warranty service but thought it was something simple. Nothing inside is simple on a Dyson! Can the clutch be replaced and from what vendor?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

What is the best way to clean the filters ? Is there an awners maual online? I need to know how to take this apart to clean it all well.


May I get the model # so I can help you more ... Eureka 12 Amp Capture Vacuum Upright Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

Broken switch and need to know how to take apart the fein tool


... Fein Multimaster Rs - Msxe 636 - 2 Rs

I need a manual for the Eureka Capture vacumn. I have broken the belt and don't know how to take it apart to replace it.


Here is the belt you need and the manual which has instructions:Eureka Capture Replacement Belt ... Eureka 12 Amp Capture Vacuum Upright Vacuum

My grundig yacht boy 400 has a broken antenna and I would like to repair it. It came off , has small screw still attached at bottom. Need to take apart radio and don't see how. Thank you, Lourdes


... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Took canister apart to replace power cord. some grid fell out before i could see where it was. need to know where it goes


... Oreck BB2000 XL Little Hero Canister Vacuum

Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.


Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum

I don't know how to take apart me Rainbow e2 series vac.


I recently took mine apart because the motor stopped working. Realized the brushes were pretty well worn down and one side was completely gone. I was looking on the internet for detailed instructions on how to take it apart. I ended up just ripping i ... Rainbow E series Canister Wet/Dry Vacuum

NEED TO CLEAN CAP OF THERMOS VACCUM HOW DO I TAKE IT APART WITHOUT BREAKING IT?


... Thermos Vacuum Insulated 24-Ounce Stainless Steel Hydration Bottle Charcoal 24-Ounce

I need a diagram to show me how to take the machine apart to fix the turbine


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I need to take apart a vax cylinder hoover to service it


... VAX Appliances 2000 Canister Vacuum

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


You did not identify your model and the TriStar website does not provide manuals. They do have a FAQ page which does provide some illustrated guidance which may be helpful. See here:\015\012\015\01 ... Tristar Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0774 seconds