Having problems with your Hoover Vacuums ?

BELT REPLACEMENT HOOVER WIND TUNNEL VACUM CLEANER


Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

BELT REPLACEMENT HOOVER WIND TUNNEL VACUM CLEANER


... Hoover Vacuums

How to replace filter on a Hoover Mach 3.3 wind tunnel upright vacume cleaner


... Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?


Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum

Replacement belt # for hoover wind tunnel model u5750-900. original belt # 38528-035, please


Your belt number is correct ending in 035. I have had luck with belt number ending in 033 also. ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?


There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacing a belt Hoover wind tunnel - Hoover Vacuums


You will find four screws under the bottom cover. remove these. remove the beater bar, loop new belt on bar on pulley area. install the bar and then pull the belt over the motor shaft. re-install cover. ... Hoover Vacuums

Replace belt hoover 5100 - Hoover U5444-900 5100 Wind Tunnel 15 Inch Wide Hepa Filter Bagged Black VacuumVacuum


... Hoover U5444-900 5100 Wind Tunnel 15 Inch Wide Hepa Filter Bagged Black VacuumVacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Replace belt hoover u5101-930 - Hoover U5444-900 5100 Wind Tunnel 15 Inch Wide Hepa Filter Bagged Black VacuumVacuum


... Hoover U5444-900 5100 Wind Tunnel 15 Inch Wide Hepa Filter Bagged Black VacuumVacuum

How to replace belt in Hoover U5402-900 Wind Tunnel Vacuum


... Hoover U5402-900 WindTunnel Vacuum

HOW DO I REPLACE THE DRIVE BELT ON A HOOVER WIND TUNNEL SELF PROPELLED


Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You ha ... Hoover Company Wind Tunnel U53019 Upright Vacuum

How to replace belt on Hoover Wind tunnel vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=831441\015\012Generic problem for all Vacuums\015\012How to replace belt on\015\012Posted by dinosir on ... Vacuums

My beater bar on Hoover Wind Tunnel 7500 has quit turning. I already replaced the belt. It worked for a while, but now it has stopped and is burning out.


... Hoover WindTunnel Rewind Upright Vacuum Cleaner

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

My Hoover Wind Tunnel has a burning smell when running. I replaced the belt, but this didn't help.


Its clogged my vax does that burning smell when it gets clogged up thats for the five minutes before it overheats and stops ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to replace the belt for hoover wind tunnel model#u6485900


... Hoover Vacuums

How to replace belt on Hoover U6626-900 Wind Tunnel bagless.


Hello,Click this to go to a site that will show you (complete with illustrations) how to change belt.http://www.info-vacuum-clea ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Wind Tunnel U6437-900. The brush will not turn. I have replaced both of the belts with no success. Any suggestions?


Hello,\015\012\015\012If you've already changed the belts and the machine still won't run, it can really be only a few things. \015\012\015\012The first thing you should check to make sure that the roller brush is good. Yo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover wind tunnel vaccuum cleaner i need to know


... Hoover Vacuums

How do you change the Hoover wind tunnel belts?


If you turn the vacuum over there will be (4) screws that hold on the base cover for the roller brush. Remove the screws and the cover and you can get to the belt(s). You can get replacement belts here: ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hoover Wind tunnel self propel not propelling - how do I know if it is the belt or the idler arm?


... Hoover U6485-900 Windtunnel Bagged Upright

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0915 seconds