Having problems with your Hoover Vacuums ?

Replaceing the circut board henry hoover

\015 Need to replace the circut board on my henry hoover\015

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replaceing the circut board henry hoover

... Hoover Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

I was using my Henry Hoover as usual. When i sucked up quite a fair sized puddle of water. The hoover instantly cut out and a strange burning smell was coming from it. Would this be the fuse, motor etc ? Or would it be worth my while just replacing the entire hoover ?

Hi. I have to wonder why anyone would **** up a puddle of water with a dry vacuum cleaner (with no earth lead). I realise that your question may simply be a joke, but if you are serious, I think it is probably fair to assume that it is now dead and p ... Vacuums

Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re

Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum

Hoover Savvy U8174-900, replacement circuit board LED/Brush Motor

\015\012 \015\012 \015\012 \015\012 \015\012 ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Hoover S3670050 how do I open the unit up, to replace a cicuit board?

... Hoover Vacuums

How do you remove the front wheel of a henry hoover as i have to replace it with a new one.

... Vacuums

Henry hoover cuts out

A 5amp fuse will struggle on start up on anything over 1000watts. Check the rating plate on the appliance for total load ... Numatic Henry Bagged Canister Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray

This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy

Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Numatic Henry Hoover

They should just pull out with a little pressure and a pair of pliers. Good luck with your repair ... Numatic Henry Bagged Canister Vacuum

Henry Hoover throwing trip switch in house

Sounds more likely to be the switch than the motor, especially if it is the model with the top switch rather than the side "rocker" switch. If you are in the UK, speak to the technical people at ... Numatic Henry Bagged Canister Vacuum

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?

... Miele SEB 213-2 Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?

Probably needs a new hose. ... Vacuums

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.

The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a

... Hoover S3670 Bagged Canister Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

How to replace power cord on Hoover WindTunnel upright vacuum

The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to acc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover Handle Release Pedal Replacement--How is it possible?

If you look at the picture, the slots are right across from the drive wheels, you can see the slots in the picture. Use a flat blade screwdriver. ... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

I have a replacement belt for my hoover elite 600. It's not obvious how to replace it!

Turn the vac over so the bottom is up..\015\012On the framing around the brush - there should be some screws.\015\012Take them out and the framing around the brush should pop off.\015\012Pull out the one side of the brush that the b ... Vacuums

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to

... Hoover U5344-900 WidePath Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0570 seconds