Having problems with your Hoover Vacuums ?
How do i set up my hoover aquamaster
\015 I was given a hoover aquamaster wet / dry cleaner.\015
Repair Help & Product Troubleshooting for Hoover Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do i set up my hoover aquamaster
... Hoover Vacuums
I have just got a secondhand hoover aquamaster s4470 and cant work out hoe to set it up to wash carpet
Have you tried the manufacturers website. sometimes you can download the manual for your appliance ... Hoover Vacuums
My Miele S5211 has lost suction power on max setting. I put on min setting to hoover chairs now when i turn upto max says on min setting
... Miele S5211 Deep Black Vacuum Cleaner Bagged Canister Vacuum
Hoover aquamaster recently purchased hoover aquamaster, trying to shampoo carpet, can't get water to come down tubes, water keeps going into dirty water tank.help!!!!!!!!!!!!!!!
Sounds like you need to attach the air hose\015\012\015\012with reservoir in place you clip on the lid with tubes attached, one of them goes down to the floor cleaning nozzle, the other tube should be about 20cm long with an end piece, ... Vacuums
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?
Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.
I have a kirby G4 hoover which set on fire yesterday burning my hand and giving me a electric shock who can help me with this?The hoover is serviced regually by a kirby engenere it was done 4 week ago and didnt seem right from then.What are my customer rights on this matter
Call or go to him explaining this matter. They should inspect this again since they had done service work t your expense ... Kirby Ultimate G Bagged Upright Vacuum
Dirt finder I have a Hoover U6439-900. After the cleaner was used a few times, the dirt finder light cycles between green and red on the regular setting and will not go to green. On the sensitive setting, the red light stays on most of the time. I have tried to run the cleaner to remove any dirt but have not solved the problem.
The sensor may be bad, or it may be coated over with dirt. Re,ove the hose at the back of the vacuum, the head of the sensor is down inside that opening, reach in there and clean it off and see it that corrects the problem, if not replace the sensor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.
I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Hoover FLair bare floor switch setting does not work.
... Hoover S2220 Flair Bagless Upright Vacuum
Hoover savvy no suction on carpet setting
Check to make sure you hear the vac. motor is running when in that position. The switch in the handle could be bad if it is not. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
My hoover steam vac keep setting off circuit breaker
Hoover windtunnel vacuum overheat switched is set off too frequently and I cannot finish vacuuming the house in one session. Lemon?
Please remember this part is doing a service to you. its basically saying my motor is getting so hot picking up this dirt that i better make him rest before he burns up. in most cases you will find that you either have a clog or your filters need to ... Hoover Vacuums
My Hoover steam vac is stuck on the tools setting and wont stop leaking water from the tools hose
... Hoover Vacuums
Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.
These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums
On hoover steam carpet cleaner, the brushes do not rotate on low or high settings.
Follow these steps if the Brushes Fail to Spin\342\200\242If the brushes on your Hoover carpet cleaner fail to spin, there may be a problem---some sort of blockage---with the suction or with the belt that turns the brushes. \015\012Turn t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hello I need a set of rear wheels to my TurboMaster Hoover. If you provide me an Email address, I can send you the drawing + picture. Is it possible to purchase it from you. (I'm living in Israel) Best Regards Zeev Priester 24 Beit Ha'Shita st' PO Box 698 Bat-Hefer 42842 Israel Mobile: +972-(0)52-4299716 Email: [email protected] [email protected] SKYPE: zeev.priester
... Hoover Vacuums
My hoover steamvac f5868900 has somehow been set to ''tool mode'' and I don't see a way to switch to ''clean mode''
... Hoover F5872-900 SteamVac Wet/Dry Vacuum
Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.
Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums
No manual We lost our manual for our hoover steam vac. Set it up and water doesn't release. What's the problems?
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=618767&thid=797691\015\012No manual\015\012Posted by mwood16 on July 17, 2008\015\012We lost our manual for our H ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Unblocking sinks Can someone please tell me how to set up my kirby hoover to unblock my bathroom sink the sales man did show me a few years ago but i have lost my manual and cant remember??? Many Thanks Nina
Remove the brushead and attach the adapter (round cup-looking device with a screen or grille on the front).Attach the hose to the blower (bag) side of the machine.In your attachment caddy,there should be a round rubber attachment with rubber teeth ar ... Kirby Ultimate G Bagged Upright Vacuum
On my Hoover Savvy U8174-900 on carpet setting, the brush spins when I pull the vacuum towards me, but stops when I push it forward. Belt is tight and fine.
Hoover savvys have two very common problems that cause this. The first and most obvious is the belt that you checked already. Many times the belt is tight but those particular belts have teeth and should you lose any teeth on the brushroller OR th ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum