Having problems with your Hoover Vacuums ?

My hoover U6485 heigth adjustment slips to low setting

\015 Height will not stay adjusted to any position except low.\015

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover U6485 heigth adjustment slips to low setting

... Hoover Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.

You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.

I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Height Adjustment on Hoover Wind Tunnel doesn't seem to do the job.

... Vacuums

How to adjust hoover u6439-900 brush on settings?

Click here for the manual > http://hoover.com/file/500/ ... Bissell 6594 PowerForce Bagless Upright Vacuum

On hoover steam carpet cleaner, the brushes do not rotate on low or high settings.

Follow these steps if the Brushes Fail to Spin\342\200\242If the brushes on your Hoover carpet cleaner fail to spin, there may be a problem---some sort of blockage---with the suction or with the belt that turns the brushes. \015\012Turn t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Levels/Settings I am having trouble changing the setting on my vacuum from 1 or "Low, Hard Surface" to any other setting. Without changing it, I am unable to vacuum on my carpet, since the setting is too low.

These height adjustments are designed so that they will not adjust when the handle is in the "back" position. This is so they will stay where they are set and not self-adjust while you are vacuuming. To change the setting, you need to return the hand ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Height adjustment won't work on Hoover windtunnel

In my experience, Hoover height adjustment are "stops" rather than being attached to an axel. Look for something that rould resemble a set of circular steps somewhere in the path the axel would take as it goes up and down. It is usually on the unde ... Vacuums

My Miele S5211 has lost suction power on max setting. I put on min setting to hoover chairs now when i turn upto max says on min setting

... Miele S5211 Deep Black Vacuum Cleaner Bagged Canister Vacuum

Brush bar not spinning when set to high or low on carpet

1) adjust the belt, see for broken or worn, and replace2)see for brushroller obstruction, and clean it and repair3) see if the brushroller without belt run smooth, otherwise repair and fix it.Lubricate.4)See if the motor run without load( ... Vacuums

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.

On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

What's your problem?I have to replace the power switch on my Hoover U6485-900. What part do I need to orer? Wher can I order it?

... Hoover U6485900 Bagged Upright Vacuum

Vacuum height won't go on low carpet setting. Dial will go on medium and high, but not low.

Make sure you're not trying to adjust w/ handle in upright locked position because thewre is a cam which raises the vacuum head a little bit when handle is locked in upright position. If this is not the problem, turn vacuum upside down with handle in ... Hoover Vacuums

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.

... Vacuums

I have a Kenmore sco 150 slow cooker. It has 3 settings. They are 12 and auto. What is the low setting for heat?

... Vacuums

Dirt finder I have a Hoover U6439-900.  After the cleaner was used a few times, the dirt finder light cycles between green and red on the regular setting and will not go to green.  On the sensitive setting, the red light stays on most of the time.  I have tried to run the cleaner to remove any dirt but have not solved the problem.

The sensor may be bad, or it may be coated over with dirt. Re,ove the hose at the back of the vacuum, the head of the sensor is down inside that opening, reach in there and clean it off and see it that corrects the problem, if not replace the sensor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would

... Hoover L2310 GUV Central System Vacuum

I have a kirby G4 hoover which set on fire yesterday burning my hand and giving me a electric shock who can help me with this?The hoover is serviced regually by a kirby engenere it was done 4 week ago and didnt seem right from then.What are my customer rights on this matter

Call or go to him explaining this matter. They should inspect this again since they had done service work t your expense ... Kirby Ultimate G Bagged Upright Vacuum

Is it possible to adjust the head for a thinner carpet (right now it's on a setting that works for a thicker carpet, so it doesn't pick up anything on a thin carpet). Is it possible to adjust the head and if so how? Also, how do you wash the filter?

... Eureka 4700A Maxima Bagless Upright Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?

... Kirby Heritage II Vacuum

Height adjustment The height adjustment button on my upright is nonfunctional.  The Height is set closest to the floor and it makes it difficult to move on medium height carpet.

You'll have to turn the upright to its side to show the sole plate where the rolling brush is. Check where the front wheels are located and ensure there is no blockage obstructing the rotary dial. Sometimes the spring mechanisms can work themselves l ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

My Rainbow E2 has been working great for years now, but recently it has stopped working on the vaccuuming setting, but will still run on the low speed air cleaning setting. I hope it is something as easy as replacing the switch. Would appreciate any tips to determine if that is the issue or possibly something larger. Tks in advance for the info/help.

Still need help, let me know.\012\012Thank you,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?

Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5342 seconds