Having problems with your Hoover Vacuums ?
The spinning brushes are not turning on my Model #F330-900 Steam Vac with rinse....
What could be my problem?
Pull the brush block out, is the shaft still on the top of it or did it break off? If it is ok, then the turbine is most likely bad. The turbine is what drives the brush block. Also make sure the little screen filter is clean.
Repair Help & Product Troubleshooting for Hoover Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The spinning brushes are not turning on my Model #F330-900 Steam Vac with rinse.... What could be my problem? Thanks MC firstname.lastname@example.org
Pull the brush block out, is the shaft still on the top of it or did it break off? If it is ok, then the turbine is most likely bad. The turbine is what drives the brush block. Also make sure the little screen filter is clean. ... Hoover Vacuums
I own a Hoover Steam Vac Plus w/ Rotating Brushes (model#F5871-900), when I turn on the power I hear a medium-loud hum coming from the motor area and nothing works. What could be the issue?
The motor sounds locked up. Water gets in there and rusts the pieces together. The motor could be replaced, but probably not repaired. ... Vacuums
My hoover steam vacs brushes will not turn . could there be a belt broken? I have misplaced the manual
For the manual:\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf\015\012\015\012For the brushes:\015\012(1) Ass ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??
This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum
Hoover F7458900 steam vac brushes won't turn
No, there is a turbine that turns the brushes. You can take the top cover off to get to it, open it up and clean it out and then try it again. If that doesn't work, then replace it, or just replace it to begin with. ... Vacuums
Hoover Steam Vac Dual V Model F7223-900 brushes will not turn
Brushes Hoover steam vac f5906-900 .can,t get the brushes to work. Is there a belt that could have broke
This machine has no belts. There is an air driven turbine that propels the brushes. If you look under the little glass window at the left front corner of the machine, there is an intake screen just above the indicator dial. That screen is there to ke ... Hoover F5906-900 Upright Steam Vacuum
Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.
On steam vac round brushes rotate until on carpet but pressure of carpet causes mechanism to slip so brushes do not turn. What is the fix please.
Hi the problem you are having is with the drive belt, it has stretched and this is causing it to slip when under pressure, the only real option would be to get a replacement belt and get it fitted how ever i have heard of people wrapping strong tape ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
My brushes won't turn on my Hoover Steam Vac Cleaner. I have removed them and cleaned them and put them back in and they still won't turn. Any suggestions?
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Steam vac brushes don't turn
This video may help you http://www.youtube.com/watch?v=QBtWcC4gqjY ... Vacuums
Brushes turning slow on Hoover F5881-900 steam vac
There is a part inside called the turbine which needs to be replaced or cleaned. Also clean the brushes. ... Hoover F5881-900 Vacuum
Hoover Steam Vac Dual V brushes won't turn
The brushes are driven with air pressure from vacuum motor. The switch merely opens a small door to allow air flow. usually there is a screen that is plugged that stops air flow which stops the brushes from turning. I too only used the appliance once ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
Hoover Steam Vac - Brushes not turned, no suction power
The Brushes not spinning is most likely is caused by seized bearings in the turbine, requiring shop service (easy fix). The suction issue can be caused by the standpipe seal missing or lower recovery tank not on properly, on some models missing front ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The Brushes will not turn on the F7225-900 Steam Vac
... Hoover F7225-900 SteamVac V2 Upright Vacuum
Hoover steam vac dual brushes will not turn.
The belt is broken. ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum
The brushes won't turn on my hoover steam vac dual v
Hi There,\015\012\015\012Unfortunately the answer above is far from helpful. The filter has absolutely nothing to do with your brushes not spinning, and you can really replace the turbine yourself without having to take it into a shop t ... Hoover F7220900 SteamVac V2 Upright Vacuum
Roatary brushes do not turn on my hoover steam vac dualy
The machine uses an air powered turbine which typically rusts and then locks itself up Ive been able to fix it in the past but its best to replace the whole assembly ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The Brushes don't turn on my Hoover Steam Vac DuetV
CHECK INTERNALLY SOMETHING MIGHT BE BLOCKING THE BRUSHES TO MOVE.CLEAN THAT MANUALLY AND TRY. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net
What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums
Brushes will not turn - Hoover Steam Vac Dual V w/ SpinScrub Vacuum
The turbine which drives the brushes is defective. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
Brushes on Hoover Steam Vac F7441-980 do not turn.Brush control on;drive pin present;filter intake clean; Drive mechanism doesn't appear to be turning. Also when spraying on cleaning solution, spray comes out in streeks rather than the width of nozzle. JBB
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Brushes wont turn on hoover steam vac f7431-900
Need replaced TURBINE AND GEAR ASY \015\012part no: 91001097 ... Hoover F7431-900 SteamVac Vacuum