Having problems with your Hoover Vacuums ?

The brushes will not turn on my up right hoover stean vac


Answers :

Take out the brush block, check to see if the shaft is on it or broken off, if broken off, replace the brush block. If it is ok, then turn it on and see if the square hole is turning, if not then the turbine is bad. The turbine is what drives the brushes. If the little screen filter is clogged, and if the foam filter on inside of the recovery tank lid is all of the way up, pull it down leaving at least a 1/4 in. gap from the top. These 2 filters can cause odd problems.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes will not turn on my up right hoover stean vac


Take out the brush block, check to see if the shaft is on it or broken off, if broken off, replace the brush block. If it is ok, then turn it on and see if the square hole is turning, if not then the turbine is bad. The turbine is what drives the b ... Hoover Vacuums

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover stean vac dual with 5 brushes


I think this is the same unit I have, I might have a couple of solutions. No, there is not a belt that turns the brushes and there is not a fuse.\015\012\015\012First of all, make sure the brushes have been clicked into the machine properly. T ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum


... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Steam Vac - Brushes not turned, no suction power


The Brushes not spinning is most likely is caused by seized bearings in the turbine, requiring shop service (easy fix). The suction issue can be caused by the standpipe seal missing or lower recovery tank not on properly, on some models missing front ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My brushes won't turn on my Hoover Steam Vac Cleaner. I have removed them and cleaned them and put them back in and they still won't turn. Any suggestions?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes turning slow on Hoover F5881-900 steam vac


There is a part inside called the turbine which needs to be replaced or cleaned. Also clean the brushes. ... Hoover F5881-900 Vacuum

Hoover Steam Vac Dual V brushes won't turn


The brushes are driven with air pressure from vacuum motor. The switch merely opens a small door to allow air flow. usually there is a screen that is plugged that stops air flow which stops the brushes from turning. I too only used the appliance once ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Hoover steam vac dual brushes will not turn.


The belt is broken. ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

Hoover F7458900 steam vac brushes won't turn


No, there is a turbine that turns the brushes. You can take the top cover off to get to it, open it up and clean it out and then try it again. If that doesn't work, then replace it, or just replace it to begin with. ... Vacuums

Hoover Steam Vac Dual V Model F7223-900 brushes will not turn


... Vacuums

The brushes won't turn on my hoover steam vac dual v


Hi There,\015\012\015\012Unfortunately the answer above is far from helpful. The filter has absolutely nothing to do with your brushes not spinning, and you can really replace the turbine yourself without having to take it into a shop t ... Hoover F7220900 SteamVac V2 Upright Vacuum

Roatary brushes do not turn on my hoover steam vac dualy


The machine uses an air powered turbine which typically rusts and then locks itself up Ive been able to fix it in the past but its best to replace the whole assembly ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The Brushes don't turn on my Hoover Steam Vac DuetV


CHECK INTERNALLY SOMETHING MIGHT BE BLOCKING THE BRUSHES TO MOVE.CLEAN THAT MANUALLY AND TRY. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net


What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

My hoover steam vacs brushes will not turn . could there be a belt broken? I have misplaced the manual


For the manual:\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf\015\012\015\012For the brushes:\015\012(1) Ass ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes on Hoover Steam Vac F7441-980 do not turn.Brush control on;drive pin present;filter intake clean; Drive mechanism doesn't appear to be turning. Also when spraying on cleaning solution, spray comes out in streeks rather than the width of nozzle. JBB


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes wont turn on hoover steam vac f7431-900


Need replaced TURBINE AND GEAR ASY \015\012part no: 91001097 ... Hoover F7431-900 SteamVac Vacuum

Drive went out on my Hoover Steam Vac Shampooer and brushes won't turn plus there's a burning smell coming from it. Only used it 6 times - bought it in March - 2008.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=761326\015\012Generic problem for all Vacuums\015\012Drive went out on my\015\012Posted by buster_lls o ... Vacuums

Brushes will not turn - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


The turbine which drives the brushes is defective. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1752 seconds