Having problems with your Hoover Vacuums ?

Hoover 1800w upright vacuum clearner on off switch to repair

\015 On off switch to replace cable\015

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover 1800w upright vacuum clearner on off switch to repair

... Hoover Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike

Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.

This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums

Hoover u6425 switch replacement - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace the switch hoover UH70015 - Hoover UH70015 Bagless Upright Cyclonic Vacuum

... Hoover UH70015 Bagless Upright Cyclonic Vacuum

Cannot find repair manual for Hoover H3044 - Hoover Floormate H3000 Upright Wet/Dry Vacuum

I found the inner round valve where the tube connects for the cleaning fluid was stuck shut. Although the "trigger" was working fine and the rod pushed againstthe valeve it wasn't working. Here's how I found this out. I tried to blow air through it a ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover dual v steamvac turbine repair - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I Have a hoover purepower 1800w upright vacuum cleaner that works perfectly except for it wont stand upright anymore. Any advice

Not sure what model of Hoover you have, you may need a new handle release. ... Vacuums

Wind tunnel by Hoover, vacuum will not turn off by using switch on upright handle. do not see a way to get to switch. modle no. U5458-900

Follow the cord and look for screws inside the bag compartment at the top. a panel should lift off allowing access to switch and cord. If swtch is melted it must be replaced with special hoover switch kit which has new wire and heavier duty switch. b ... Vacuums

Bare floor switch do not light up are work - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

F7210-900 steam vac repair book - Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum

... Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum

Hoover U5280-900 upright bagless vacuum twin chamber has a broken slider (switch) to go from tools to floor and carpet--what is the part called?? Indicator knob or cam activator?? where to order it??

... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums


I have one of these too and it used to keep cutting out, replaced the filters and now it wont even turn on.  changed fuses everything, and now im stuck with a dirty house.... ... Vacuums

Switch from tool use, to floor? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Can't expose switch to test it - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Greetings,This is a relatively easy fix for you. What I've done for you is take pictures of this repair on your type of vacuum to make it ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

On/off switch not working - Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Please make sure the mounting screws that attach the upper handle to the lower handle are tight. This sets the proper spacing of the switch rod to the switch. If this does not help, you could remove the upper handle and cycle the switch with your f ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Hoover Tempo on-off switch - Kirby Ultimate G Bagged Upright Vacuum

... Kirby Ultimate G Bagged Upright Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac

... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.4663 seconds