Having problems with your Hoover Vacuums ?

Spin brush on hoover model f5914900 not working

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Spin brush on hoover model f5914900 not working

... Hoover Vacuums

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.

You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom

... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?

I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900

May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?

Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Brushes won't spin on a Hoover Steamvac SpinScrub Model F5918-900

Well the hand tool works off the suction of the machine and has nothing to do with the turbine that controls the brushes. if you can get the part i can walk you through taking it apart. when you write back, let me know what the model num of your mach ... Vacuums

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]

The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?

On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman

\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

The brush on my bissell helix (model 22C1-2) stopped working all of a sudden today. The hose still sucks and everything. I even cleaned the spinning brush and it still doesnt work. I just bought it in August.

... Vacuums

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.

- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.

... Vacuums

Hoover Spin Scrub Model F7412-900. Will not work

... Hoover Vacuums

Model #5880-900 Hoover spin brush carpet cleaner

The brushes on the Hoover steam spin will not move. ... Hoover F5906-900 Upright Steam Vacuum

Brushes dont spin on Hoover Steam Vac Model F5919-900

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?

Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0924 seconds