Having problems with your Hoover Vacuums ?

My vacuum cleaner does not suck

\015 All filters are clean\015

Answers :

Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

Vacuum Cleaner sucking dirt out of the cannister instead of into it.


Where you put your hand is supposed to ****.are the filters dirty?if so clean them.disconnect the hose completely from the vacuum and see if you can blow through the hose,if you can't blow through the hos then the hose is clogged.you can run a garden ... Eureka Whirlwind 4496 Bagless Upright Cyclonic Vacuum

My vacuum cleaner is not sucking. It's overheated and stopped


In this case it is motor problem, you can sort out only by calling the technician. Call the customer care and check out the cost for repair, if it is very high you can go for a new one and be in peace of mind.Thank you. ... Sanyo Performax SC-U126 Vacuum

Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance


... Kenmore 34722 Grab-N-Go Upright Vacuum

I have a Bissell powergroom vacuum cleaner and i sucked water into it and now it wont even turn on what could be wrong with it??? It was a very expensive vacuum and i dont want it to be thrown out


... Vacuums

Hello, we have a Miele cat and dog turbo 5000 vacuum cleaner which we bought in December. It has just started blowing air out of the grid on the top of the cleaner instead of sucking from the tube. The whole top section which is opened to change the bags doesn't seem to want to clip down properly either. Do you have any ideas> I'm gutted as it was so good until this happened. Thanks Michelle.


The lid not closing properly is almost certainly the cause of your problem. Without that lid sealed tight to the body you will get no suction through the hose. So, the question is: why isn't the lid clipping down properly? Did you just change the bag ... Vacuums

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned


... Electrolux Vacuums

Is there a reset button for the bissell healthy home vacuum cleaner? I was vacuuming and sucked up a door mat and it turned off and will not turn back on


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Bissell proheat is blowing not sucking air - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell vacuum cleaner has stopped sucking things up as well as it was when I first purchased it two months ago. It also seems to be pushing more air out than it is sucking up.


With most vacuum cleaners the problem stems from carpet fuzz (especially in new carpet instalations) to build up of pet hair I have repaired several vacuum cleaners & my solution has use a shop vac if possible 15 amps or more clean the hose, check th ... Vacuums

Suction problems My Hoover elite vacuum (which is less than a year old) is not sucking up properly. Also, when I detach the tube that goes to the vacuum cleaner so I can add my attachments, it blows OUT dirt through that opening. HELP!


Sounds like a clog right near the front ... Hoover Elite U5061-900 Bagged Upright Vacuum

Xl silver is not sucking - Oreck XL Deluxe Vacuum Cleaner Vacuum


Make sure belt is on and it is not clogged ... Oreck XL Deluxe Vacuum Cleaner Vacuum

Vacuum cleaner hi.this is 10 yrs old and not overly worked.bags are changed regularly and the micro filter has been changed at least three times over ten years.it goes well for about 2o minutes then loses power with not much "suck"after that.sometimes shutting down completely,because of overheating i presume,or just carries on at a much lower'"suck".have tied shaking bag inside but no luck.any suggestions out there or can you tell me the agents support office for new zealand[auckland].many thank


What brand vacuum is it? ... Vacuums

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

It is not sucking the water back up. - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


There is a handle u hold down when u push the vac forward and thbat sucks up the water ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The bissell proheat turbo carpet cleaner is not sucking up the water from the vacuum or the tool attachment.


Bissell cleaner will not **** up water??? ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My hoover steam vac is not sucking up water - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a egomaxx 1800 vacuum cleaner which is not 'sucking' up at all well. There is no obvious blockage.


Sometimes the blockage is within the hose itself and not easy to spot. The only thing that can keep a vacuum from sucking is somekind of blockage. It is rare that a motor have lost power because of a short thats why it is not sucking, and it would be ... Vacuums

Electrolux z5525 vacuum cleaner not sucking properly


... Electrolux Vacuums

I sucked up a dusing cloth with my ducted vacuum cleaner and now it does not **** at all. Help can not afford a three hundred dollar bill. blocked


Hi,Turn off the power on the main vacuum unit. Then thread a plumber's snake or stiff small gauge wire from the outlet you were plugged into when the dust cloth got sucked up. With any luck, you'll be able to push it through a bit or with a sma ... Emerson Vacuums

My vacuum cleaner is not sucking up anything off the floor


... Fantom Vacums Vacuums

Hi, I have a whirlpool 7700 Power Clean vacuum cleaner - the built in kind. It's not sucking very well. The motor still runs and I've cleaned out the collector. Any suggestions?


... Vacuums

Not sucking up the water, motor runs? - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Vacuume cleaner not sucking up properly. Have replaced belt but belt keeps snapping?


Check to see taht with no belt in place the brush roll turns freely.There should be no resistance. If not remove hair and thread from ends of brush Then check the leveling screws on the end of the brush to be sure they are adjusted evenly. ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0973 seconds