Having problems with your Hoover Vacuums ?
Beater bar bearing lubrication
\015 What should be used to lubricate the bearings on a beater bar? Will oil get gummed up from all the dust? Could graphite work?\015
Normally the bearings in brush-bars are sealed bearings with a dust cap on both sides graphite would be best,, but the best bet is get two new ones off EBay there very cheep to buy,,,
Repair Help & Product Troubleshooting for Hoover Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Beater bar bearing lubrication
Normally the bearings in brush-bars are sealed bearings with a dust cap on both sides graphite would be best,, but the best bet is get two new ones off EBay there very cheep to buy,,, ... Hoover Vacuums
Beater bar bearing lubrication
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.
It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum
Beater bar is seized up. How to unclog bearings?
Spray it with WD40 ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum
I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely
The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.
Hi,\015\012\015\012There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. Al ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?
... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum
Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.
Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan
Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum
I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.
I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum
My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My beater bar makes a noise and has a crack in the motor on the beater bar and is discolored--me thinks I need a new motor for the beater bar
Sounds like you're right. New motors are available at your nearest Aerus Electrolux store. They used to charge the same amount for selling the motor and letting the buyer install it, or for installing it in the shop. Worth checking in to.\01 ... Electrolux UltraLux 2000 Bagged Canister Vacuum
My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.
Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn
The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums
Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.
The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums
We have a dyson dc14 and the beater bar stopped turning, we cleaned the bar off and checked the belt and it's not broken, I know I called Dyson a year or two ago and they told me how to reset the beater bar motor but I don't remember exactly what I did, anyone know the answer to this??? thanks in advance....
Hi its Darran at Dyson.Check that the brush control dial is in the centre position when the machine is locked upright. When you release the head and pull the handle back this dial should mopve forward to the on position. Once here, the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My dyson dc25 vaccum lock for the beater bar keeps comming unlocked,i use a screw driver to lock the bar side door ,but the carpet seems to unlock when i use it and if i don't watch it the beater bar will slide out we baught the unit about four months ago and love it
Beater Bar I can't get the beater bar to stop...any suggestions?
Something may have come apart under the nozzle cover, you will have to take the cover off to see. Including a picture, maybe it will help.\015\012\015\012 ... Miele S184 Powerhouse Bagged Upright Vacuum
My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?
You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The beater bar on my Kirby Generation 3 does not turn when it is on. I took it off and cleaned it but I am not sure which way to put beater bar back in. The ways I tried, it still doesn't work.
First - make sure that you are installing it right - see online manual HERE . If you still can not get it working right - issue new ticket and explain in more de ... Kirby Generation 3 Bagged Upright Vacuum
Beater bar in my dirt devil vision wobbles around the center shaft. Took of beater bar and it sounds like sand in it when shaken. Can this be disassembled?
From your description, if your beater bar was wobblying, ther may be more damage to the base of the vac than initially seen. Dirt Devil has different number of warranties in number of years for thier vacuums. I would check with your nearest dealer. L ... Vacuums
I sucked up a piece of fabric and turned it off ASAP. Now the beater bar won't work, but the beater bar does turn. Help!
If the clothe is jammed in the power head you will need to clear it. Have the unit unplugged and manually rotate the beater bar to work the jammed material out. Sometimes a pair of pliers helps to grip the material while turning the beater bar. If th ... Vacuums
Have a dyson vacum and the beater bar stopped working. How do you fix the beater bar.
Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
While vacuuming my carpet, a corner of a throw blanket was sucked into the beater bar. I turned the vacuum off and was able to pull the corner of the throw blanket out without much resistence. I plugged the vacuum in and started it and now the beater bar isn't rotating.
Try pressing the reset button on the nozzle, probably just tripped out the brushroll motor ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum