Having problems with your Hoover Vacuums ?

My hoover 2100 over heats when used for more than 15 mins. I have checked everything there is nothing broken or blocked and it not used much.

Answers :

There's only 2 reasons that heat switch will trip.
1. Not enough air
2. Bad motor or heat switch.

I would check your filters and suction on the tools. There should be LOTS of suction at the tools on that unit. If there's not follow the air back until you find the plug. It might just be a really dirty filter or carpet powder or something along that line plugging the filter.

If the suction is not a problem it might just be defective and in that case if it's not very old go to hoovers website and find a service center location and have it fixed. They shouldn't charge you for the repair if it's still under warranty. You'll need your receipt for it though, so hope you kept that!

Good Luck!
The Vac Dr.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover 2100 over heats when used for more than 15 mins. I have checked everything there is nothing broken or blocked and it not used much.

There's only 2 reasons that heat switch will trip. 1. Not enough air2. Bad motor or heat switch.I would check your filters and suction on the tools. There should be LOTS of suction at the tools on that unit. If there's not follow the ... Hoover Vacuums

My Hoover T5703 has suddenly stopped working. I was using it, moved it to another room, presssed the start with my foot - and nothing! I have checked that the fuse and electricity socket are both OK.I did knock it over a while ago and am wondering if I have broken a bit of plastic in the foot starter. It doesn't seem to 'click' as firmly as it did, but I cannot see how to take it off to check?

... Hoover Vacuums

I have a new Hoover Dual V steam vac that I bought from a neighbor who only used it once. I have only used it once since then and it worked great. This time, because I am pregnant, I bought some non-toxic cleaner that was much thicker than the very watery Hoover soap. This vac has a wash option and a rinse option. The rinse option works (sprays and sucks properly), but the wash cycle doesn't at all-neither soap nor water comes out. Nothing comes out, but it still sucks. I took everything o

There's a powerful electric motor attached to a fan that sucks in air.Did you checked and cleaned that motor.If the dirt is got stuck up ion the motor then the motor will not spin as per its regular speed.For rinsing the motor spin on one cycl ... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Yes, they pretty much all leak, that can be chalked up to lousy manufacturing. Sorry. ... Vacuums

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t

Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Burned smell hi, I have used my hoover 4 times and is starting to smell as something burned, I checked the troobleshouting part of the owner manual and it says that check the belt, I already did that and everything is ok I used the hoover again and still smelling bad and start to work very slow I better shut off it.. what could I do??

If the motor slowed down this would indicate a bad motor. not cost effective on this model to replace unless under warranty. it is not uncommon these days to see a motor go bad every now and then.\015\012\015\012What are the first 4 digit ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

I bought a roomba pro elite robotic floorvac at a tag sale from an elderly couple who apparently used this vac very little as it was very clean and she had never even used it enough to use the extra filters that came with it, she said it was just too much for her to bend down to work it or move it. i suspect she stored it but kept the battery in it. after charging it, it powers up and sings a little tune, but then shuts off. i cleaned everything, including the sensors. it still shuts off, do you

... Roomba Pro Elite Bagless Robotic Vacuum

Our kenmore progressive model #11634922 was working fine today. And then - it's not. Plugged in - nothing is working on it. We let it cool down (though it didn't seem hot). Still nothing - no light, no motor. Tried it in some other plugs that we know are functioning well - and still nothing. Any idea what might be wrong with it? It's six years old but doesn't get heavy use. Thanks so much ~ Susan Golden

Hi, it could be a number of things, cord may be bad as well as a problem with the motor. There also is a fuse that could have blown. If you go to sears.com, click on parts, put in your model number, when the page loads, click on the first link ... Kenmore Vacuums

I got a vacumn from a friend who ungraded and though i used at her home when i got it home it would not turn on when plugged in and i check everything and no use. my friend lost her manual. im in my 60's and on a disability fixed income so cant afford to take to repair but got lots of men at church who would help if they know how to trouble shoot it. and would really appreciate any help. thank you , ann

Hi\015\012In the UK we have similar machines but they are made by Vax. If you can't source the correct user manual from Hoover.com consider the following - it is a free download.\015\012\015\012http://www.vax.co.uk/downloads/pdf/vzl-60156016_v2 ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Won't start. My son was using the vacuum & Didn't change the bag. The vacuum was making the full bag smell, but the light was't on & it didn't stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn't the problem. I've let the vacuum "rest" for several days, It still won't start. Any suggestions?

There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn't find it very useful. There was some info on how to change the powerhead drive belt. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

No I did not my hose on the dirt devil does not have much suction on it I took everything apart and found nothing wrong no clogs anywhere but when I add an attachment to the hose it loses all suction...I looked for a switch to change from regular vacuuming to attachment found nothing why is this??????? Need a manual where can I find some information and a download on line manual??????

Try this. There should be a little filter unerneath the tank. just clean that filter or replace it. (9 times 10) thats the problem.\015\012\015\012good luck. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

My Bissell BS3920F upright (similar to the 10N6F) has been working wonderfully for the past 3 years but suddenly seems to not pick up dog hair as well as it used to. It has been pulled apart by my husband to ensure nothing is blocking the hoses etc and when running the suction seems to be there. It seems to grab the dog hair and leave it in a straight line directly under the unit without picking it up. I then disconnect the hose and use to hose to pick up the dog hair. This works well but obviou

Check to see if your brush is not worn down, they do wear with age - compare the length of the bristles with a new one. Replace the brush ir there is a significant difference in bristle lengths. Also check the flexible ben ... Bissell Vacuums

I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.

... Vacuums

We have a euro pro x deep fryer model #f1075 we have only used it twice and while using it it went dead. We checked the cord and the outlet tried plugging it in another outlet but nothing. We do not have the instructions so we dont know what else to try.

... Euro-Pro Vacuums

When using my hoover wind tunnel the last few times it has emitted a burnt rubber smell so my husband checked the belt and is wasn't broken or off but now when I use the vacuum the beater bar doesn't seem to be going around as well as it should be can you help

I take it the belt was put back on !! i would say hubbi forgot the tension arm a little black striker that can go in two ways but put in back wards it will not tension the arm ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Sudden loss of suction. Using a dirt devil upright. Checked the belts that were changed recently and working. Changed the half full bag. No change. Checked for blockages and as far as I can see there are none. The blower is working as much as it ever was I think but I;m stumped.

R u sure there is nothing cought in the hose? ... Dirt Devil Featherlite Bagged VacuumVacuum

ORECK VACCUM older oreck xl, new belt , new bag, checked for clogs, does not pick up as it used to, and, much harder to push, seems to grab or drag, why????

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=747767\015\012Generic problem for all Vacuums\015\012ORECK VACCUM\015\012Posted by FISHERMAN928 on Jul ... Vacuums

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.

Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

The suction still works but the primary floor vacuum doesn't. I checked the belt and its not broken. The engine that runs the floor vacuum doesn't engage like it used to

The belt doesn't have to be broken to affect the the way the vacuum picks up on carpet. If the belt is stretched then it will slip and not turn the roller brush properly. Here is the manual and belts you need: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My bissell momentum vacuum is making a very loud noise but it still picks everything up. Do you know of a reasons why it is making very loud noises. I checked and nothing is stuck in it.

It might be the motor or the fan is messed up.have someone or you check that out. ... Bissell Vacuums

Nothing spraying out of Bissell Powersteamer Proheat. I've check filter under flow indicator, pump belt is fine, cleaner in proper tank, bladder of water tank is full. We've had it for a very long time but it's barely been used. Can anyone help?

... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

I have no suction on my vacuum, I have checked everything, belts are good, and hoses appear to be clear of any blocks, any suggestions

Please give the model number and manufacturer of the vacuum. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.8579 seconds