Having problems with your Hoover Vacuums ?
Hoover U6485900 How do I get to the motor to check for plugged inlet
Go here for manual > http://hoover.com/file/509/
Repair Help & Product Troubleshooting for Hoover Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hoover U6485900 How do I get to the motor to check for plugged inlet
Go here for manual > http://hoover.com/file/509/ ... Hoover Vacuums
Makita 440 Dust Extractor - Trying to rectify a problem, when i switch on an appliance plugged into the socket, it will not run. IS used to run with this plugged in, but the hoover motor runs no problem. Any ideas what might be amiss, or where i can get a wiring diagram? Thanks in Advance!
... Makita 440 Wet/Dry Vacuum
My hoover power drive vacuum simply died. It just shut off. I checked the plug, etc...I just can't get any power...Can you help?
If no light or motor sound cord is probably bad. Look near AC plug or just replace the plug end. Check with ohmmeter for continuity with switch ON. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?
I need help in disasembling my hoover windtunnel to check the motor brushes
... Hoover Vacuums
I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?
Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums
The pump motor in my Bissel Proheat 2x Plus seems to have failed. It was seized so I sprayed WD-40 in it and let it sit for 3 days. Now I can turn it by hand, but when plugged into the unit it still doesn't spin. Here's a picture: http://bbay.dreamhost.com/bissel_proheat_2x_plus/P1070021.JPG I wanted to take the motor out and hook it into another power source to see if I can get it going but it has 3 wires. I'm used to only 2 (+ and -). How can I hook the motor up to another power source,
... Bissell Vacuums
Motor problem When i plug my steam vac in the motor sparks and smokes. It smells as if the motor is burning out. I've tried different outlets through out the house and get the same outcome, what can i do to solve this?
Nothing you can do im affraid its the motor armature so unless it can be stripped down then you will need to replace the motor i would get a price for the motor to decide if it is worth doin sorry. ... Vacuums
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.
The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums
My Hoover wind tunnel keeps overheating and the red I dictator is on. I have cleaned all filters and checked for clogs....could the motor have dust in it? How do I check?
Okay. I read these posts and decided to take the advice of checking the hose.I had cleaned all filters, checked all hose (as-is) and did belt checks, etc.The indicator was always showing red and it would shut down after about 5 minutes. ... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner
Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re
Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum
My Hoover sprint 1700w has stopped working. I thimnk it could be the fuse. How do i get the plug apart to get the fuse out? Can you give me other possible reasons it could have stopped working?
I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped
... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
Our kenmore progressive model #11634922 was working fine today. And then - it's not. Plugged in - nothing is working on it. We let it cool down (though it didn't seem hot). Still nothing - no light, no motor. Tried it in some other plugs that we know are functioning well - and still nothing. Any idea what might be wrong with it? It's six years old but doesn't get heavy use. Thanks so much ~ Susan Golden
Hi, it could be a number of things, cord may be bad as well as a problem with the motor. There also is a fuse that could have blown. If you go to sears.com, click on parts, put in your model number, when the page loads, click on the first link ... Kenmore Vacuums
Stopped working hello im in france, so my henry has a two pin plug. i feel all that needs changing is a fuse, but i carnt find it. i have taken out every possible screw searching for it but to no luck. iv checked and cleaned wireing and checked cable for nicks. im now begining to think maybe the motor has gone?
Hi! Sorry you've had to wait so long for a reply, but I've only just stumbled upon your problem. You probably don't need help any longer, but here goes anyway!\015\012You will not find a fuse, because there isn't one. If your Henry ... Numatic Henry Bagged Canister Vacuum
I have to go into the garage to turn on the motor on the tank and to shut it off. When I plug the hoses into the outlets in the house, it doesn't turn on the tank motor. I don't know what part to get and nobody in Raleigh, NC shops can help me.
Is this Electrolux that's now known as Aerus? If so, take it in to the Aerus Electrolux store for a tech to look at. You can find the nearest Aerus Electrolux store by following the instructions on the site at bottom of page.\015\012\01 ... Electrolux Central Vacuum
Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.
Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl
There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums
I have a Vacu Queen V3000 and it stopped working in the middle of a job. I verified that I have power at the outlet that it plugs into and then checked motor resistance from the plug and I got about 600 ohms. What is the problem?
EMRS, Hahah the same thing happened to mine... the lid cracked and I used PL Construction adhesive, it has held for a year, but needs constant gluing. Where can I buy a new lid relatively cheaply? Can't find one in Canada. ... Filter Queen Majestic Canister Vacuum
Am attempting to get 'inside' the vacuum to troubleshoot why it suddenly stopped running. Suspect it may electrical, and have already checked the obvious (visible cord and plug.) However, there doesn't seem to be an obvious way to get inside the canister without destroying something. Thanks!
Hi There,\015\012\015\012Here's a link to a repair solution that I've done explaining how to diagnosis the cord reel, and open up the machine. The model this is done on is not the same exact model as yours, but the repair will be almost ... Miele S251 Flamenco II Bagged Canister Vacuum
I was cleaning my carpet using my hoover steamvac ls. I had already changed the water 3 times. The last time, the water ran out and I kept running it for a couple of minutes trying to **** up some of the water off the carpet when it just shut down. I check the breaker and the outlet and they were OK. Checked my manual for troubleshooting; couldn't find an answer there. Do you think I burned the motor up (I didn't smell anything) or will I have to send it in for repair? When I clicked on your web
(1) take the tank off and reassemble to assure you sealed to the lower handle.\015\012(2) the water feed has nothing to do with the motor or electrical, purely mechanical.\015\012Hoover web site is free, no cost. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Needs new motor have the part but cannot get into the part of the hoover where the motor goes
Have a look at www.dysonmedic.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a Simplicity (Danby) SDR458H Dehumidifier. The bearings in the fan motor have become loud and scratchy sounding (due to a plugged-up filter in the past). I would like to get a repair manual for it with part numbers so I can order a new fan motor.
... Simplicity Vacuums
Is there a trick to getting the belt on the motor pulley and brush on the Hoover Elite Supreme
Hi ,try warming the belt up in hot water first it will stretch better\011 ... Vacuums