Having problems with your Hoover Vacuums ?

Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good

Answers :

Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel pulley, the tensioner is not functioning properly and will need to be replaced.
\015\012Also ensure that the brushroll can spin freely by hand, as these have a tendency to melt at the ends and seize the brushroll. I have also seen the groove that the v belt fits into melt itself out of round, which can cause the same symptom as you're describing.
\015\012Keep in mind as well that while the rubber belt may appear to be ok, it does have to be replaced every 3-6 months whether it breaks or not. Even though it hasn't broken, if you were to hold it up against a new belt, you would see that the old one has stretched significantly: which can decrease the machine's ability to rotate the self-propel transmission pulley and, in turn; the brushroll.
\015\012Feel free to contact me with any further questions.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good

Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel p ... Hoover Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?

... Bissell 8910 ProHeat Clear View Upright Vacuum

Electrolux Epic 6500 SR Carpet Sweeper won't go on. Belt good brush moves, bulb looks good, reset red button I'm not sure, works, looks good. Vacuum starts has suction ,

This link is the manualhttp://www.totalvac.com/manuals/electrolux_manual_Epic6500.pdf ... Vacuums

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.

Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Bissell 9200 pro heat carpet cleaner , brushes won't turn, both side belts are good. bad brush motor? or brush moter belt?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

No suction My vacuum does not seem to have much suction when in use. The agitator brush is rotating but I'm not able to get much off the carpet. The suction is fine when I use the attached wand.

If the belt is stretched, then it can't turn the brush rol under load, if you haven't chenged it in the last 6 months, then I would put a new one one. Also check the dirt inlet by the brush roll for a blockage. ... Riccar 8955 Upright Vacuum

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.

Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.

The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Dyson is not picking up on the carpet as good as it use to. The brush doesn't seem to engage on the carpet unless I hold the angle upright. It's very uncomfortable to hold it at that angle. What would correct this problem?

Brushes do wear out. Compare the length of the bristles on you brush with a new one. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush assembly will no longer spin on carpet however the suction from the system is still good. Unit is only 5 years old.

Probably a seized beater roller (the bearings wear out). Just order the new part and replace it and you'll be one your way again. And of course maybe a belt. ... Electrolux Centralux Vacuum

Does not vac carpet well brushes spin and are clean no cloggs and wand works good

It could be that the belt is worn. You can get replacement belts here:Replacement Vacuum Belts ... Vacuums

Make a very loud noise when I try to vaccuum the carpet. It sounds like it's something in the brush up front. Belts look good and obstructions are gone. Not sure what else to do.

\015\012Try to lower your wheels a bit which will raise your vacuum a little off the ground. When you vacuum a bare floor you want the vacuum as close to the floor as possible. When you vacuum a carpet if you don't r ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The hose works great, but when I try to vacuum the carpet it doesnt work. The brush is turning, but I don't feel much suction. I checked for a clog and didn't see any.

You probably need the clutch replaced. This needs to be done every 1 to 2 years for most people ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Good day, I have a EN Vision Dirt Devil upright, 12 amp, wide 15" nozzle. My vacume is blowing out insead of sucking up the dirt from the carpet. Can you help me? What should I do? Thank you very much for your time. Judy 1/19/11 [email protected] 602-670-4170

It's probably the brush "kicking" the dirt out, rather than it being blown out. This happens if there's a clog in the airflow system somewhere. This could be anywhere from the power head above the brush to the tank where the hose connects.\01 ... Dirt Devil Vacuums

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN

First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha

I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha

You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie

The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0892 seconds