Having problems with your Hoover Vacuums ?

Need drive belt

\015 I bought a v belt and drive belt the drive belt is to big so the roller doesn't turn. Can you please tell me why?\015

Answers :

I'm guessing you have a hoover self propel windtunnel. If that is the case then you should bought the V belt suffix 034 and Flat belt suffix 035. The belt numbers should be listed on the serial tag though.
\015\012
\015\012With most hoover two belt systems there is a pulley that is supposed engage when you recline the machine and this will apply tension to the V belt and tighten the system up so that the brush will spin. If you hold it upside down with the bottom plate off, and release the foot pedal, you should be able to see it happen.
\015\012
\015\012Occasionally that pulley gets stuck and on some newer models they are prone to breaking as well.
\015\012
\015\012Make sure the machine isn't set to floors.
\015\012
\015\012Good Luck
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.


Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Need to find the belt for the brush. Every sight leads me to drive belts and I dont need that. I need a model number prefferably


Unscrew both bolts that are in plain sight on top of vac above the brush, then remove housing and belt is right there ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need a drive belt for Shark vac. Model number UV210BS---The small belt that drives the larger belt for the beater .


... Vacuums

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.


HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

I just bought a Hoover Power Drive Concept Two Electronic vacuum from the thrift shop. It only needed two belts and seems powerful. But i don't understand what the small red button on the handle marked "Release Drive" means. Thanks for any insight! Anything else i need to know about this machine? Is it a good one? Are there high-performance bags available for it?


The U6311-903 is a self propelled vacuum. The the small red button will stop the handle from moving back and forth, which makes the machine go foward and backwards. The red button disengages the self propelled feature. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

Need drive belt


I'm guessing you have a hoover self propel windtunnel. If that is the case then you should bought the V belt suffix 034 and Flat belt suffix 035. The belt numbers should be listed on the serial tag though.\015\012 ... Hoover Vacuums

I need to replace belt-drive cog belt - Eureka Vacuums


Go here > http://www.eureka.com/en-US/Vacuums/Accessories/Belts/ ... Eureka Vacuums

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.


Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim


Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Have bought a black ad decker band saw DN33 9 needs new drive belt but has 2 on parts list which 1 do i need


... Black & Decker Vacuums

Dyson fan belt fitting. i've lost my manual for my dyson animal dc07 and need to fit a new drive belt. thanks in advance, alan


You can see this on utube video. help ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP


Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?


Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

Need part # for drive belt


Here's a link to the schematics. It diagrams each part and it's number. Best of luck.\015\012http://www.vacuum-depot.com/parts.asp?SchematicID=190 ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I need a new belt drive gear.


Here's the Bosch website where you can order from the parts list . http://www.boschappliances.com/site_tools/orderparts ... Bosch BUC11700UC Cyclone Jet Bagless Upright Vacuum

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa


Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

I need to know how to repalce the drive belt in a Sebo upright cl


Thanks to its automatic height-adjust feature, the Sebo X4 has two drive belts, one from the motor to the height-adjust sensor, and another from that sensor to the brush roller. To access them,first remove the base from the handle, undo the four rece ... Sebo Air belt K3 Bagged Canister Vacuum

I need to replace drive belt on dyson dc17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Here is a link to the belt you need and a manual you can view which has instructions: Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need a drive belt for he 3108 Bissell Easy Vac. Brush doesn't turn.


You can get the belt you need for the Easy Vac here:Bissell Easy Vac Replacement BeltAnd here is a link to the manual ... Bissell 3108 EasyVac Powerbrush Upright Vacuum

The self propelled feature does not work. Belts are OK but the drive wheels do not seem to be engaging. Is there a cable or something from the lever on the handle that needs to be replaced?


My vacuum cleaner does not turn on \015\012could it be the motor out \015\012i check the switch it ok not getting any power to the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

NEED TO REPLACE DRIVE BELT ON HOOVER VACUUM MODEL TURBO 3500


Take off the brush roll cover, then take out the screws from the bottom to remove the top lid, the belt goes from the brush roll to the motor shaft. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0563 seconds